evision num : 750 
   - Usb reset issue changes.
	 - Version number fix for USB.
	 - Removed commented code in usb_main_osd.c file.
Revision num : 751 
	 - Committed latest pmemdata with buffer full workaround (Host is not receiving packets)
Revision num : 794 
	 - Powersave changes merged into driver
	 - Multiple vap support
	 - AP mode encap/decap changes
	 - Removed redundant broadcast/multicast flag setting in ndiface.c
	 
Revision num : 795
   - Merged Manufacturing related changes in the version before 794.
   - Added driver modes --- "PER + loopback", "PER + loopback + calib", "qspi flashing".
   - Informing the driver modes to firmware through reset mac frame.
Revision num : 797
   - In receive.c channel programming is disabled every time (after first programming).
Revision num : 898
   - matlab utils rf_lbk m2,m3, rf reset,end point, soc_reg_R/W, unknown command check
   - onebox utils antenna select
   - pmemdata_burn for flashing contents
   - flash_contents to be burnt onto E2PROM
   - upgrade.sh for upgrading contents onto E2PROM
   - Addded support to load different fw depending on driver mode
   - bb reset fucntion added
   - 40mhz upper/lower fix added (sending radio caps added)
Revision num : 943
   - EEPROM read values support added
   - Added flash diectory in release for calibration of cards from MATLAB
   - Support for calib burn from MATLAB is added
   - pmemdata with new latest EEPROM read values support addded in release 
Revision num : 944
	- Added Legacy power save changes, More data bit handling for unicast and broadcast
	  packets, PS_NOTIFY frame addition, DTIM beacon gated frame bit setting etc.
	- Multiple Queues added for AP mode. Now maximum queues are 12.
	- RTS/CTS changes were added. Sending rate settings for Self cts frame.
Revision num : 980
	- Firmware changes for legacy powersave, broadcast data handling taken.
Revision num : 1031
	- Bug fix for onair management pkts, which got inserted by mistake in earlier commits
Revision num : 1051
	- Power save Changes(IOCTL, Traffic based PSP, Fast PSP)
Revision num : 1054
	- Moved notify scan done after returning to BSS channel
	- ndiface.c (Traffic based PSP calculation)
	- Power save changes 
Revision num : 1096
	- Added new state in pwr save state for deep sleep during connection.
	- Checking traffic only if traffic based and pwr save is enabled.
	- bug fix for mod_timer, when expire is multiplied with Hz giving an huge value and timer is not expiring.
	- Power save changes and added data pkt dumps in receive path before giving to reorder function
Revision num : 1104
	- reading mac address from flash
Revision num : 1109
	- Taken TA firmware for 1103 trunk and committed pmemdata.
Revision num : 1115
	- Mac addres related changed pulled from trunk to tag_0p3.
	- Incremented driver release num to 10
	- Disabled EEPROM in menu config
Revision num : 1122
	- Station to station fixes
	- AP mode fixes
	- Security bug fixes, Encrypt bit is set in descriptor based on per ni flag.
Revision num : 1124
	- Compilation error fix for USB mode
	- Writing into wakeup register is disabled in USB interface mode.
Revision num : 1129
	- USB Compilation error fix.
	- USB power save changes.
	- committed pmemdata (1128 version of wlan_0p3 tag)
Revision num : 1135
	- Clearing skb flags in send_data_pkt_to_drv func
Revision num : 1142
	- Transmit PER packets are sent in queue no "0"
Revision num: 1195
	- Buffer full fixes for AP mode
        - Flags commonality in skb, mbuf, netbuf
	- Rx STBC, Greenfield support addition in AP mode
	- TSF related changes
Revision num: 1208
	- HR timer disabled
	- Broadcast pkts are sent in Beacon queue
	- Txop values are given from host for beacon queue
	- Pmemdata changes committed (SVN rev:1207)
Revision num: 1214
	- Default rate settings in case of fixed rate is corrected according to protocol mode choosen.

Revision num:1221
	-Order of IE's is modified. WMM comes first followed by HT params.
	-Station to Station bug fixes. Encryption enable bit is set for Broadcast/Multicast pkts

Revision num:1229
	- Powersave changes pulled to trunk
	-Host encap aggregation fix, Host encap compilation fixes

Revision num:1238
	- Net80211 based reordering algorithm is being used.

Revision num:1241
	- HR timer based beaconing is present for AP mode with USB interface.
	- Monitor interval fix in onebox_util.c

Revision num:1243
	- Updated the pmemdata.

Revision num:1249
	- AP mode encap bug fix made. Setting 8023ENCAP flag in onebox_core_vap.c.

Revision num:1268
	- Pwr save monitor interval limiting fix.
	- Crash fix in send_auto_rate function.
	- Sending uapsd params only when uapsd_acs is a non zero value.

Revision num:1294
	- Allowing Uapsd wakeup_period value zero.

Revision num:1318
	- Reordering changes in reorder.c file
	- Removed onebox_devdep_ps.c and added onebox_ps.c.
	- Merged ULP related changes.
	- Moved Powersave related code to onebox_ps.c from onebox_core_vap.c


Revision num:1320
	- Merged Wifi Direct Changes 
	- Sending block/unblock frame only in STATION mode

Revision num: 1345
	- Merged CSR releated per mode stats changes, eeprom version.

Revision num: 1346
	- Aggregation fixes for PER mode.

Revision num: 1397
	- Added four Separate Queues for AP in the following Order
    4 for STA + 4 for AP + 1 MGMT + 1 BROADCAST + 1 RESERVED + 1 BEACON

Revision num: 1400
	- Insertion of wlan Modules(.ko) and Firmware loading is from the current path of driver, not from /home/rsi/release
	- You can verify from insert.sh script

Revision num: 1401
	- Removed the unused functions of reordering.
	- Added support for scan after connection. Does host triggered bgscan when scan is issued after connection.
	- Bgscan IOCTL error handling in IOCTL path.
	- Added beacon_interrupt stats.
	- Removed onebox_ba.h file.

Revision num: 1412
	- Moving the driver to INIT state when beacon miss is observed, previously we used to move to scan state directly.

Revision num: 1434
	- Beacon alignment fix in send_beacon.

Revision num: 1449
	- Added WEP Shared key Support in both AP and Station Mode.
	- Changed in notify.c, so that P2P works on all VAP's

Revision num: 1450
	- Fix for P2P mode in send_beacon

Revision num: 1455
	- Merged Hw beacon miss changes, Slot updation, Rx filtering, Short/long preamble changes
	- CSR changes merged in to the trunk
	-Pmemdata is picked from the WLAN_0P5 tag with the ppe stuck fixes

Revision num: 1542
	- Added debug prints in ordered way.
	- Bgscan parameter IOCTL request changed.
	- sending radio_caps frame after connection only for station mode.

Revision num: 1546
	- Added new (loopback) pmemdata_lpbk firmware in release directory for driver_mode 3
  - Committed PER mode extended desc changes in pkt_pro.c

Revision num: 1550
	- Added pmemdata with 40Mhz fixes for channel nos in 2G

Revision num: 1551
	- Added pmemdata_lpbk with 40Mhz fixes for channel nos in 2G

Revision num: 1552
	- Added filtering mechanism in Net80211 to drop any packets coming from unconnected peer
	  in station mode
	- Removed frame descriptor size filling in desc word 0 in the program_bb_rf function
	- tid filling in ht.c 

Revision num: 1562
	- Allowing arguments up to 50 in ioctl.
	- Error messages in IOCTL.
	- Commented RSN IE in probe requests.

Revision num: 1564
  - existing supplicant removed

Revision num: 1565
  - new supplicant 2.1 added

Revision num: 1572
	- Bug Fix in Supplicant in events.c file. Scan Fix

Revision num: 1574
	- Bug Fix in Send_beacon

Revision num: 1577
	- AP mode Powersave Bug fix.
	- Beacon INterrupt is moved to beacon INDication pkt.

Revision num: 1584
	- Stats receive changes to stop sending request again
	- Bootup params changes for correct M N P values for both 20 and 40 MHz 

Revision num: 1586
	- Onebox_proc_zone enabled crash fix.
	- Authentication to previous AP Bug fix(wlan-375).

Revision num: 1614
	- Bug fix in sending radio_caps frame.

Revision num: 1625
	- took latest matlab_utils.c file with the receive stats bug fix
	- Bug fix in sending radio_caps frame.

Revision num: 1698
 	- Disallow HT info in WEP/TKIP in AP mode. 
	- Station to Station data transfer bug fix in bsd.c file.
	- Disallowing vap creation twice bug fix.

Revision num: 1708
  - WiFi Direct Bug Fixes

Revision num: 1717
	- Not allowing vap creation in PER mode.
	- Changing the EAPOL pkts priority to Mgmt queue at the time of connection.
	- Dropping data pkts other than EAPOL until a Node is authorized.
	- Disallowing HT rates in WEP/TKIP modes.
	- Auto rate bug fix for Mixed TKIP mode.

Revision num:1724
	- Firmware updated with latest firmware.

Revision num: 1725
	- Sending delete peer notify to firmware when ni is not equal to vap->iv_bss

Revision num: 1736
	- Sending sta_leave when an authentication is recvd from already associated station.

Revision num: 1740
	- Corrected HTCAP to HTINFO in adding htinfo_body.

Revision num: 1743
	- Keep alive feature updated.

Revision num: 1744
	- compilation errors solved.

Revision num: 1746
  - Changed Best_RSSI_Selection According to New_Supplicant_2.1. Changes done in events.c file

Revision num: 1755
	- Bug fix for Junk IE's in beacon/probe resp.
	- Bug fix for USB driver. Indicating USB_DIR_IN for read_pkt.

Revision num: 1759
  	- Support added for flash updation without corrupting the mac adrress and calibration values.

Revision num:1763
	- Adding fix for autonomous GO test case(6.1.2) in WFD Interop test plan.

Revision num:1798
	- Broadcast deauth fix
	- Reorder header space fix

Revision num:1807
	- per receive changes addition of rssi reporting, define's for basic stats
		and complete stats,
	- In end to end receive stats changing rssi paramter to bea_avg_rssi

Revision num:1820
	- WLAN-687 -Fix for driver getting stuck when AP mode is started in the same channel running PER traffic
	- SIFS, SLOT TIME  commented in firmware

Revision num:1824
	- added preamble support changes in transmit.c

Revision num:1838
	- Association ID increment fix.
	- Sending delete notify when deauth is received in ASSOC state.

Revision num:1842
	-Txop values programmed in microseconds (usecs) in radio caps frame

Revision num:1860
  -matlab utils changes for RSSI reporting. macros added 
  -bypassing mac address reading for calib mode

Revision num:1867
	- Sending deauth only for association->auth state when deauth is received.
	- Basic rates bug fix for probe response.
	- Null data bug fix for keep alive packet. Enabling M_ENCAP when we are sending pkt to raw_xmit.
	- Indicating sta_id for pkts to encap in mgmt queue.
	- Sending self deauth bug fix in AP mode.
	- Changed beacon interval minimum value to 50ms.
	- Handling of tx_key_idx when its value is greater than 3.

Revision num:1869
  - WFD bug fix (Non ERP-bit set and privacy bit)
  - Bug no : WLAN - 724 and WLAN -725 in Jira.

Revision num:1874
  - Discarding mgmt pkts only for retried pkts which matches with our rxseq.
  - Instead of queuing null data for station in pwr save, setting tim feild in
    beacon.

Revision num:1881
	- Added Sniffer Mode. Pending List in Sniffer Mode : AMSDU, AMPDU handling, RSSI, timestamp, Datarate, CRC status.

Revision num:1888
  - No changes made. Just restoring the accidentally removed Driver folder. This will be equivalent to 1881 svn version in trunk path.

Revision num:1889
	- Added Max_QUEUE limit for queues.
	- Writing to PS-wakeup register after writing pwr save disable pkt to firmware.

Revision num:1896
	- Work around for vap ptr corruption

Revision num:1952
	- DPD channel power programming taken in mgmt.c file.
	- WMM param ioctl changes, AMPDU tx/rx aggr disable ioctl added
	- Firmware updated

Revision num:1954
	- Seprate wm structures for station mode.
	- Allowing bgscan_ssid lessthan 32 characters.
	- Pwr save bug fix.

Revision num:1959
   - ULP changes

Revision num:1995
	- WLAN-664 (Observed station is not getting disconnected from AP when we AP is giving broadcast diassoc packet) bug fix
	 condition check in ieee80211_sta.c improvised
	- Channel power is taken from user input in per mode
	
Revision num:1997
  - loading pmemdata_lpbk for all rf_evaluation driver mode
  - Setting bb_rf_event only when scan confirm is received.
  - Committing pmemdata & pmemdata_lpbk of rev 1996

Revision num 2042
	- Committing mic indication code for counter measures validation
	- eeprom v5 support firmware updated

Revision num 2047
	-Added support for Master Read/writes.
	-Debug frame support added.

Revision num 2070
	- Bug fix for wlan-601, removed unused variables in ieee80211_output.c

Revision num 2072
	- Traffic based and fast PSP bug fixes.
	- Group key renewal changes.

Revision num 2107
	- Frame_desc correction in sending EAPOL frames in send_onair data pkt function(Bug fix for WLAN-863).
	- Changed disallow_ht rates function to work for WPA2 mode. 

Revision num 2132
	- Removed pwr save print before getting vap ptr to avoid crash.
	- Indicating Probe req cnfrm irrespective of success/failure confirm.

Revision num 2134
	- Bug fix when probe req failed is recvd.
Revision num 2140
	-Compilation warning fixes for USB mode
	- Added proc stats for ap mode specific data tx packets.
Revision num 2315:
	-Coex code with flashing changes. 1.0 Bug fixes pulled in
Revision num 2317:
	-Dual band bg scan bug fixes
	-Enabling immediate wake up bit in disable powersave frame.

Revision num 2319
	- Added callback for sdio_master_access_msword

Revision num 2337
	- Reverted watchdog timer changes

Revision num 2340
	- reseting conn_in_prog flag at peer_notify in station mode is in  wep and open modes.

Revision num 2347
	- Watch dog Reset changes
	- Load /unload feature.
	- Separate coex_mode for WLAN, WLAN+BT, WLAN+ZIGBEE
	- Separate scripts for Coex modes.

Revision num 2348
	- Excluded firmware active checking for Flashing Mode.

Revision num 2349:
	- Bootup params changed
	- proc stats corrected
	- Assertion A2 check added

Revision num 2364:
	- Iwconfig display bug fix for WEP mode.

Revision num 2380:
	- Bug fix in sending bootup params.

Revision num 2395:
	- Allowing OFF channel beacon parsing.
	- MIC failure indication based on status received from Firmware.
	
Revision num 2397:
	- Modified folder names in osi_wlan/devdep path
	- Modified onebox_wlan folder name to wlan_hal.

Revision num 2428:
	- ULP changes for common Hal.
	- Per TID aggregation support.
 	- Moving vap_state to SCAN when deauthentication is received.

Revision num 2433
	- start_p2p.sh script added in release
	- took latest pmemdata

Revision num 2448:
	-CPU soft lockup issue. start/stop of Net80211 if_snd_q added

Revision num 2449:
	-Dropping Pkts other than EAPOL when if_snd_q len is more than MAX_LEN and allowing only EAPOL keys in ndiface.c file.

Revision num 2454:
	-Two tid's mapped to single Access category, no of pkts to aggregate from TA to host
	is given as module parameter. 
	- Common database for running  WLAN, WLAN+BT, WLAN+ZB images from flash.
Revision num 2458:
	-Unaggregated pkt processing support in driver. Changed for minimizing cpu utilization on embedded boards
Revision num -2463
	- Keep TA in hold before giving chip reset and waiting 100ms to ensure TA processor to go to hold and any pending dma transfers to rf spi in device to finish.
	- Reseting DMA mode of RF SPI in device before programming watch dog reset. This is a fix for load/unload issue in bt mode.

Revision num -2480
	- Extracting Pkt type from data pkt received in common hal for WLAN.
	
Revision num -2487
	- Changes made for Sniffer Mode.
	- Added Timestamp, Rate in radiotap_header ndiface.c

Revision num -2492
	- Added Sniffer utility for Selecting Band Width

Revision num -2501
	- Added support for Multiple VAP.
	- Moved code of forming frame_desc before queuing the packets to queue's.
	- Separate structure for Ps_req_params.
	- Traffic Timer initialization is made irrespective of confirm.
	- Removed send_onair_mgmt function in onebox_pkt_pro.c has we moved foriming of frame_desc before queueing pkts.
	- Beacon interval will be made to multiples of 4, as we support 4 Vaps.

Revision num -2503
	- Initializing if_snd->ifq_len =0 at vap initiailization, as some times we are having invalid q_len;
	- Allowing channel programming only if Monitor or AP mode is enabled, do not allow if Station is already running.

Revision num- 2528
	- Jira bug fixes 991, 999 changes.
	- Aggregation - Initiate BA set up for the first data packet (WLAN-1017)
	- Error case handling while issuing BG scan ioctl (WLAN-766)

Revision num 2533
	- RTNL assertion warnings fix, used rtnl_trylock in ndiface.c for Jira issue -966

Revision num 2546	
	- BG scan ioctl, segmentation fault & input error correction
	- Delete vap ioctl changes, corrected input params
	-Beacon interval changes for AP & sta, separate macro maintained for min bintval for AP & Sta.

Revision num 2550	
	- Added panic_stop_all_activites function to stop driver activities in CMD write/read failures.
	- handled negative cases in Receive path, based on length recvd.

Revision num 2556
	- driver_mode is hard coded to WIFI_MODE_ON, corrected adapter->Driver_mode as per the module param input. 

Revision num 2559
	- VAP_ID and STA_ID error Detection code, Driver will assert when ever mismatch occurs.
	- Sending bgscan and power save requests in WPA/WPA2 only if PTK, GTK and EAPOL_4 cnfrm is recvd.
	- Added sta_mode structure in adapter to know the information of our station VAP.
	- Added ha_vap_info structure for maintaing all VAP information in HAL.
	- Addded station_cbl_t to know the information of ni and VAP of a particular sta_id.

Revision num 2565	
	- RTNL assertion bug fixes

Revision num 2566
	- supplicant issuing scan ioctl is being executed after some delay(apprx 10sec)- JIRA WLAN-1018 fix
	- Problem with the trunk driver has been corrected

Revision num 2567
	- Added CRC indication in Sniffer Mode.
	- Loading Firmware separately for Sniffer Mode.

Revision num 2588
	- Fixed compilation warnings.
	- Removed unused variables.
	- Loading PS_REQ and bgscan after installing PTK, GTK and EAPOL_4 after 100ms timeout
	- Saving sta_mode information in adapter->stamode structure when STA_CONNECT event is received.
	- Dump_stack instead of KASSERT in negative cases.
	- WLAN-1056 bug fix changes 
Revision num 2597
	- Support For WEP_Shared Key. 
	- Encryption in Net80211 layer

Revision num 2606
	- dev_close crash issue resolved.
	- msleep removed in core_os_intf.c file
Revision num 2612:
	- Bug fix for issue  WLAN-1092.

Revision num 2622
	- [Jira- WLAN- 1058] crash on coex base on linux kernel 2.6.38
	- [Jira- WLAN-1121] avoid sending peer notify twice, due to which dumpstack() messages are appearing in the logs
	- [Jira- WLAN- 1080] Max num of bg scan channels corrected
	- [Jira- WLAN- 1111] Max probe req len corrected, due to which bg scan ssid can be given upto max len 32.

Revision num 2629
  - Removed Loading keys as NULL when EAPOL4 failed.

Revision num 2630
	- Pulled the brach wlan_1.0.1C changes to trunk
Revision num 2634
	- Power save changes after review.
	- Listen interval hardcoded to 8
	- [Jira -WLAN-1122] - WPS IE is removed from BG scan probe request 
Revision num 2642
	- Powersave changes, removed unnecessary code which is in commented section earlier.
Revision num 2643
	- [Jira- WLAN-1090] Changed the interrupt registration code inorder to avoid reset issue

Revision num 2647
	- Unknown symbol bug fix during insertion of wlan modules.
Revision num 2655
	-[Jira- WLAN-1093]  Switching of context from wlan_remove to receive thread while remove is in progress allowed some queued Rx packets to HAL
		Sending wlan_deregister frame after all the Net80211 and Thread handling gets completed.
Revision num 2674
	- Issue sending unencrypted packets in ap/station modes. Code changes related to it committed.
	-AHB master writes and reads related changes in onebox_debug.c
Revision num 2680
	- SDIO chip reset issue changes 

Revision num 2684
	- Bug fix for allowing pkts in open mode and dropping pkts for node which doesn't have Encryption set i.e allows only after installing keys for that node.

Revision num 2732
	- Per mode changes for wifi only mode

Revision num 2740
	- WLAN BUG - 1081
	- Sniffer Mode changes.
Revision num 2758
	- Support for kernel version 3.14

Revision num 2751
	- Not waiting for rtnl_lock when delete vap is called through IOCTL path, as it is been acquired when an IOCTL is issued to driver.
	- Power save bug fixes: Not making decissions when we are in process of roam and connection.
	- Locking the code in processing the recvd pkt and at some places of checking and making the decissions based on VAP state,
		as at any point we may recv an interrupt to delete vap. To avoid Null pointer dereferences.
	- Bug fix for sending Group key in AP mode. Sending Sta_id for Station mode and VAP_ID in AP mode.
	- Running the recv pkt processing in Interrupt context mode.
	- Compilation error fixes for interrupt context.

Revision num 2777
	- Made Mcs Information Changes in ndiface.c for Sniffer_mode.

Revision num 2795
	- Added callback in ic structure to stop initial timer(traffic timer ) when connect command is received from supplicant.
	- Removed hardcoding on unblocking station data queues for P2P mode.
	- Calling send_block_unblock with appropriate macro instead of 0's and 1's.
	- Added dump_stack in sta_join1 when station receives reassoc cmd.

Revision num 2801
	- Separate data queue stats for AP and Data pkts.
	- Storing sta_mode Vap_id when station mode vap is created.
	- In node.c Searching for the station mode vap in the ic->list, previously we are using TAILQ_FIRST.

Revision num 2807	
	- TX aggr limit (no of aggr packets) increased to 11 instead of 6. This changes is as part of fixing the low throughput issue.

Revision num 2811
	- queue_work api name modified. Took firmware version 2810 from trunk.

Revision num 2833 
	- Common host usb driver changes merged

Revision num 2835
	- Missing usb folder in Rev version 2833 is added and committed.

Revision num 2839
	-[JIRA  WLAN-1210] Corrected porting issue related to threads for kernels below 3.x

Revision num 2857
  - Added a Check in Sniffer.c so that it wont accepts invalid ch_bw values. (BUG WLAN-1204)
  - Added code in ndiface.c (BUG WLAN-1211)

Revision num 5805
	- Sending Immediate wakeup in WLAN deregister frame.
	- Writing to wakeup register while resetting the chip in removal process.
	- Checking bssid in deauth frame with vap->iv_bss->ni_macadrr instead of ni->ni_bssid.
	- Not allowing power save profiles(Fast/TPSP) to modify or take decissions until initial timer expires. 
	- Enabling INT_CONTEXT by default.

Revision num 5813
  - Not calling onair_mgmt_dump when it is Sniffer_Mode.(Jira BUG WLAN-1223)

Revision num 5820
  -Dual band changes, Reading operating band from EEPROM instead of hardcoding in driver

Revision num 5822
	- Support for pmemdata_wlan_bt_classic and pmemdata_wlan_bt_le added. WIFI+BT coex mode is split into WiFi+BT classic and
	WiFi+BT-LE modes.
	- Modified MISC_CONFIG_HOST_CTRL_REG address in usb probe function from 0x40150012 to  0x40150038

Revision num 5849
	- Enabling 40Mhz by default.
	- Disabling 40Mhz when Concurrent AP and station modes are running.
	- AMPDU_RX changed to 16k in ASSOC_REQ.

Revision num 5890
	- Semaphore(ic_lock_vap) syncronization between delete_vap, TX_path and RX_path.
	- Running the RX_path in WORK_QUEUES context for SDIO also.	

Revision num 5894
	- Work around for disconnecting station when we have connected to AP in 40Mhz only in concurrent AP and STA modes. 
	- Reverted counter value to 4 instead of 6 in core_wlan.c 

Revision num 5902
	- ZigBee
	- Updated APP (switch) by end device poll data

Revision num 5914
	- Freeing core_data and core_data->ampdu_info ptr memory in core_deinit.
	- Replaced init_done with init_net80211_done, Setting this at core_net80211_attach and resetting in core_net80211_detach.

Revision num 5926
	- Reset issue fix on embedded boards. Corrected the address of the data to be aligned in ulp_reg_write() function.

Revision num 5935
	- Auto flash mode changes for sdio interface

Revision num 5937
	- Committed latest images of wifi, wifi+bt-le , wifi+bt-classic, wifi+zb into svn

Revision num 5987
	- Manual flashing mode added for sdio/usb interfaces.

Revision num 6076
	- Auto and Manual flash changes committed in tag were applied to trunk

Revision num 6082
	- switching qspi clock to 80Mhz during 40mhz bandwidth operation
	- Short gi rates are set based on the AP's configurability of channel bandwidth
	- handling of 802.11 data packets (QOS Null data packet) in Net80211 modified based on M_DECAP flag.

Revision num 6087
	- [JIRA - 1238] Observed power save is not getting enabled when station is rejoining to AP some times. Fix made in peer notify function.
	- Fix for station not connecting to AP with better rssi. Fixes made in supplicant code for indicating the rssi level of better AP.

Revision num 6092
	- [JIRA - 133] handling of immediate wake up bit corrected in onebox_common_tx.c
	- [JIRA - 125] - removing /var/run/wpa_supplicant during remove_all.sh to ensure clean exit of supplicant code
Revision num 6107
	- Roaming between AP's with different ssid.
	- BG scan ioctl related syntax & segmentation fault fixes.
Revision 6184
	- Eliminated DFS channels in scan list
	- Bug in autorate frame for indicating specific 11n rates
	- P2P connection problem due to dropping of beacons and probe responses. 

Revision num 6208
	- [Jira GWBCE-169] Driver is not getting removed in usb mode
	- Eliminating DFS channels while bg scan ioctl is issued
	- avoiding sending null data pkt in 5ghz with 1mbps data rate

Revision num 6209
	-[Jira - GWBCE 141] Cmd53 failures when data transfers happening b/w OBM AP and thirdparty station
	-[Jira -GWBCE 140] crash fix when running concurrent ap/sta modes and deleting sta/ap vap while data transfer is
	going on

Revision num 6219
	- [JIRA -GWBCE-179] ACL policy module is built.Access control policy mechanism verified	

Revision num 6271
	-[Jira -GWBCE-186] Bug fix for  Powersave functionality is working as expected in USB mode	
 	-[Jira -GWBCE-185] Autorate functionality  not working as expected
	-Error condition added for avoiding 5ghz channel programming when card supports only 2.4Ghz

Revision num 6289
	- Committing Revision num 6271 changes from tag to trunk.

Revision num 6313
	- [Jira GWBCE-190] - Stopping multicast queue and not resuming it properly due to which EAPOL pakcets are not coming from Net80211.
			Dropping the multicast/Broadcast pkts when water mark level is reached.

Revision num 6347
	- jira bug fix on autorate 

Revision num 6369	
	- Monitor mode vap is not getting deleted. Bug fixed by making proper checks in delete_vap ioctl.

Revision num 6401
	- Stopping cancel_remain_on_channel timer when cancel_remain_on_channel ioctl is recvd from supplicant.

Revision num 6515
	- Software boot loader code changes as part of release 1.1 committed.

Revision num 6516
	-scripts and .rps files added in release folder.

Revision num 6571
	-committing bootloader and flash burning firmware binaries.

Revision num 6645
	- Added 40Mhz suport for AP mode and simultaneous AP and Station mode.

Revision num 6670
	- Added error handling/ timeout cases in software boot loader code. 

Revision 6678
	- Software boot loader code, optimizations.

Revision 6691
	-Commiting boot loader changes from trunk database to 1.0.1e without 40Mhz changes.

Revision 6706
	- CRC checksum calculation for verifying calib data added
Revision num: 6739
	- Dynamic vap updated frame changes. Sends this frame when user ISSUES, RTS and Fixed rate IOCTL and change in Protection Bit from beacon is observed.

Revision num: 6748
	- Changes of RX filtering frame.

Revision num: 6763
	- one's compliment checksum additions

Revision num: 6770
	-Compilation support for kernels till 3.16.0.

Revision num 6821:
	- Command values changed for load and burn fw, checksum offset changed, erase bootloader option added

Revision num 7002:
	- Flash read chunk size buf fix SDIO case.

Revision num 7012:
	- USB vendor ID added, compilation changes for Raspberry Pi

Revision num 7028:
	- Removed calculate_checksum function and added checksum_onescompliment file for calculting CRC.
	- Updated Bootloader files.
	- Enabling WPS_2.0 support in supplicant.
	- pulled Booloader bug fix from WLAN_1.0.1e tag.

Revision num 7034:
	-Support for Powersave in PER mode.

Revision num 7156:
	-Support for rf power modes via ioctl and broadcast filtering.

Revision num 7162:
	-Support for rf power mode in PER mode.

Revision num 7276:
	- Submitting Urb's after loading Firmware.

Revision num 7329:
	- Hardware beacon miss support.
	- Ps_params IOCTL changes added support for no_of_dtims sleep, dtim_interval_duration, listen_interval_duration.
	- Added common_dev_config_param.c file  and Frame for configuring the common dev_config params.

Revision num 7331:
	- Writing into ULP register to reset the chip.

Revision num 7339:
	- Including hostapd-2.3 for supporting AP with Enterprise security.

Revision num 7344:
	- Common hal power manager changes.

Revision num 7354:
	- Progamming bb_rf when there is a change in rf_power mode value.

Revision num 7356:
	- Keep alive ioctl and iwlist support added

Revision num 7370:
	- Modified the dev_config params, as per requirement and removed Ulp sleep threshold and Lp sleep threshold.
	- Modified the range of supporting values for no_of_dtims_per_sleep and dtim sleep interval.

Revision num 7397:
	- Disabled listen interval duration, dtim listen interval duration, num of dtims per sleep field settings from user space via onebox_util.c

Revision num 7421:
	- Changed the tx_power variable from unsigned int to signed int to accept negative values.
	
Revision num 7435:
	- Writing into SDIO WAKEUP register is disable during disable of Deep sleep.

Revision num 7473:
	- TX_access bug fix for BT_LE mode and zigbee.

Revision num 7474:
	- Hostapd 2.3 work around added in ap_drv_ops.c

Revision num 7475:
	- Changing retry count to 7.

Revision num 7477:
	- Changed the Name of ALLOW_BEACON_ASSOC_PEER to DISALLOW_BEACONS.

Revision num 7479:
	- By default ALlowing All the broadcast data.

Revision num 7504:
	- [WLAN-1478] - Removing of onebox-hal proc entry twice has been avoided

Revision num 7525:
	- Load prog values code removed. BB/RF values will be loaded from TA only. Removed the menuconfig option of bbp/rf 
	programming via driver/TA.

Revision num 7532:
	- Crash bug fix during simulatenous card detach and rmmod of modules.
	- Throughput bug fix for concurrent AP and STA mode.

Revision num 7550:
	- NULL Pointer dereference bug fix in power save confirm.

Revision num 7576:
	- Removed code of hr timer.
	- Added stats of TX_ACCESS in common hal proc entry.
	- Indication of disconnect event to supplicant in AP mode.
	- UDP RX out of order bug fix. The issue fixed by indicating pkts to OS by using function netif_recieve_skb instead of netif_rx.

Revision num 7595:
	- Added changes for mentioning retry count for probe responses and EAPOL.
	- Added retry count in extended descriptor. 

Revision num 7614
	- added num of dtims per sleep in ps_req_param
 
Revision num 7617
	- Crash bug fix during vap_create. This is happening due to registeration of WLAN is happening twice.
	- Bug fix of uninstalling driver during scan phase.

Revision num 7623
	- Netlink socket changes for BT and zigbee protocols added
	- Address alignment issue while sdio read corrected.

Revision num 7624
	- Missing generic stack file operations corrected.

Revision num 7629
	- Changed netlink socket name in BT and ZB
	- Removed the USE_BLUEZ_BT_STACK macro in bt_init().
	- Some minor clean up and code indentation.

Revision num 7644
	- Changed the family name in the application for ZB netlink sockets

Revision num 7647
	- Coverity fixes for the sections USE_AFTER_FREE, RESOURCE_LEAK, MISSING_BREAK, UNUSED_VALUE.

Revision num 7736
	- Removed unused/dead code.

Revision num 7738
	- Coverity bug fixes, sizeof warnings, signed/unsigned usage, memory freeing functions changed.

Revision num 7752
	- Bug fixes for BT removal issue on different kernels.

Revision num 7756 
	- Bug fix for [Jira-1502], compilation issue for zigbee

Revision num 7760
	- Sparse warnings/ fixes in driver.

Revision num 7786
	- Added new api's and structure alignment,rejoin cases are handled

Revision num 7813
	- Modified the Bootloading sequence in onebox_common_devops.c file

Revision num 7814
	- Giving access to protocol when sleep entry is received, if the protocol has tx_intention.

Revision num 7860
	- WFA testing changes, maintained different queue depths for each queue.
	- ACM changes with out TSPEC added

Revision num 7863
	- Added support for FULL flash mode with secondary bootloader in PER mode. 
		PER RPS file name RS9113_WLAN_PER_QSPI.rps.

Revision num 7887
	- [Jira -1528] Bug fix for supplicant level- scan buffer corruption and drivercaps corruption fixes.

Revision num 7960
	- [jira - 1538]4byte master read/write changes done.

Revision num 7975
	- Compilation issue after addition of 4byte master read/writes corrected

Revision num 8110
	- Compilation issues usb mode on 4byte read/write changes corrected.

Revision num 8112
	- Added LP/ULP parameters required by f/w to module params so that user can change the parameters as required.

Revision num 8159
	- GPIO and Channel Utilization changes, ulp_ps_handshake mode is selected to Packet handshake by default  

Revision num 8164
	- Bug fix for card reset in SDIO mode . Updated the macro value of RF_SPI_PROG_REG_BASE_ADDR	to 0x40080000. 

Revision num 8168
	- Added support for UAPSD in AP mode.
	- Crash bug fix for handling OFF_CHANNEL_BEACON with BAD_LEN IE.

Revision num :8194
	- Displaying the total number of pkt received and the pkts recvd less than the threshold given by user in sniffer mode.

Revision num :8207
  - Dev_config Params frame format change.

Revision num :8208
  - Fixed bug in sending dev_config_vals frame.

Revision num :8223
  - Added support for full Flash mode for Sniffer mode.
  - Removed sleep in driver when IOCTL is issued.

Revision num :8239
  - Added NOA support in P2P client mode
  - WiFi-Direct certification changes for P2P.

Revision num :8263
  - DFS client with Quiet and CSA; with single quiet element support

Revision num :8269
  - Bug fix during DFS scan, shifting from passive scan to active scan.

Revision num :8292
  - Added support for 11d and Set Region  for station Mode.
  - IOCTL to set txpower.

Revision num :8296
  - Indicating EOSP indication in misc_flags instead of extended desc.

Revision num :8303
  - Initialising all channels according to region_domain after disconnection.
  - Allowing channel 14 to do scan if region is JAPAN.

Revision num :8306
  - Fixed rate bug fix.

Revision num :8347:
  - Allowing bgscan only in channels currently supported by the regulatary domain.

Revision num :8361:
  - Multiple QUIET support.
  - Bug fix in sending supported channel IE in assoc req.

Revision num :8376:
  - CSA crash bug fix, added timer to handle case when only a single CSA beacon is received.

Revision num :8397:
  - Usb card reset buf fix when it is unplugged suddenly. Reseting the write_fail variable when disconnect function is called.

Revision num :8506
  - Configuring LMAC clock as 80Mhz by default.
  - Changed bbp_lmac_clock division factor  of 20Mhz band to 111 from 121 in bootup_params.h file.

Revision num :8514
  - Allowing EAPOL even if we observe Queue is fill with its water mark level.
  - Reprogramming the ps timer if it expires when VAP is in transition state.

Revision num :8535
  - Programming timeout as 1000ms for usb card write.

Revision num :8576
  - Storing wep transmission key indx on per vap basis.
  - Indicating TA to Host aggr count has 1 in sniffer mode.

Revision num :8581
  - Programming timeout as 30000ms for usb card write.

Revision num :8606
  - USB Changes made for Usb Full speed compatibility.

Revision num :8653
  - Added support to do scan using iwlist command.
  - Indicating MIC failure to supplicant only for unicast packets.
  - Enabling SHORTGI_40 for AP Mode.
  - Changed do_bgscan parameter, no parameter is required to enable /disable host trigger bgscan.
  - Removed Conuntry selection from Menu config as IOCTL is implemented. 
  - Removed support for selecting Encryption using iwconfig command.

Revision num :8655
  - By Default PS is enabled for Bluetooth.

Revision num :8659
  - Trilithic release define to disable Channel utilization.

Revision num :8711
  - Bt removal bug fix.
  - Disabled bt data logs.
  - Processing 11d IE only during foreground scan.

Revision num :8725
  - Compilation fixes for 2.6.30 kernel

Revision num :8766
	- Sending soft_reset control as zero in bb_read frame. i.e. Doing baseband read without keeping baseband in reset.
	- Loading RS9113_WLAN_PER_QSPI binary in case driver_mode 3(calib mode).

Revision num :8773
  - Clearing previous SHORTGI flags before setting the Shortgi flags.
  
Revision num :8823
  - Corrected the 40Mhz flags in VAP CAPS frame.

Revision num :8975
  - Bug fix in using Context ptr after freeing the memory in usb mode.
  - Crash fix while sending common dev config params Using Interrupt context.
  - task queue creation moved to vap_setup from ifattach to avoid crash in interrupt context.

Revision num :8977
  - Support for higher kernel versions(from 3.17 to 4.0) added.

Revision num :8991
 - corrected compilation error for kernel version 3.19 to 4.0

Revision num :8995
	- Added IOCTL for GET INFO.
	- Changed proc of onebox-mobile to OBM-wlan
	- Fixes for interrupt context code.

Revision num :9114
	- 64 bit compatibility added.

Revision num :9122
  - Added Multiple URB support for WLAN for USB interface.

Revision num :9131
  - Reserving the headroom while allocation in case of usb mode.

Revision num :9142
  - Handling of coex related pkts in proto_id type conversion.

Revision num :9229
  - DFS Master and radar detection algorithm(onebox_radar.c) added

Revision num :9261
  - Passing netbuf_cb as an argument for write_pkt function.
  - Crash fix while releasing spinlock on embedded platforms.
  - Removed storing of netbuf_cb address at (data -128) location in USB mode.

Revision num :9267
  - FCC and ETSI Changes.
  - WOWLAN IOCTL

Revision num :9277
  - Android compilation fix.
  - Compilation warning fix.

Revision num :9279
  - WOWLAN Utility Added.
  
Revision num :9334
  - BT_PER changes
  - Removed GENL_STACK option from menuconfig
Revision num :9341
  - Added onebox_per.h in bt/include
  - Removed bt related structures and defines from onebox_util.h

Revision num :9342
  - Compilation warning fixes.
  - Antenna gain ioctl changes.

Revision num :9383
  - Added Limited no of stats in bt_util.c

Revision num :9405
  - Bug Fix for On chip stack.

Revision num :9430
  - Separate rps files for BT LE and Classic Per mode.
  - Change in bt per stats display.
  - Bug Fix for On chip stack.

Revision num :9454
  - Sending Vap caps frame when sethtconf ioctl is issued.

Revision num :9457
  - Changing the function "strtol" to "strtoll" in bt_transmit.c bt_receive.c.

Revision num :9472
  - Bug fix for strucking at scan states some times.
  - Sending RX MPDU density as 8usecs in ASSOC REQ. Indicating the mpdu density peer notify.

Revision num :9475
  - Sending Mapping of MPDU density value to FW.

Revision num :9478
  - Releasing semaphore before unregistering netdev

Revision num :9527
  - WLAN-1845 keep alive bug fix.
  - changes for link quality and rssi indication in iwconfig added
  - Bug fix for out of memory .
  - ANT gain ioctl for End 2 End mode.
  - Bug fix for crash while removing driver when scan strucks.

Revision num :9601
  - Bug fix for crash in reordering.

Revision num :9645
  - Not indicating scan req confirm when not in scan state.
  - Signaling probe req wait when detaching.
  - Crash fix during bt initialization. 

Revision num :9654
  - NULL pointer crash fix in bt initialization. 

Revision num :
	- Bug fix for WLAN-1905 and WLAN-1893

Revision num 9749:
	- Android specific config file changes in Makefiles
	
Revision num 9759:
  - Usb suspend and resume changes.
  - Releasing wlan tx_access when PS_STATE is in DEV_IN_PWR_SVE state.
  - Rescheduling the WLAN tx thread when PS state  is moved to DEV_IN_PWR_SVE state, when confirm is recvd from FW.

Revision 9784:
	- DFS radar detection algorithm modifications.

Revision 9791: 
	- ZigBee PER wait time increased to 100 from 2.

Revision 9795: 
  - Bug fix for crash SDIO  while sending sleep ack.

Revision 9830:
  - Compilation issues when CONFIG_PM is not enabled in lower kernels.
  - Removed get and Put usb intf functions and added resume usb intf to resume USB intf when USB is suspended.

Revision 9841: 
  - Link quality ioctl correction while displaying signal level to user.

Revision 9849: 
  - Link quality and signal strength updation.

Revision 9883: 
  - Country ioctl setting corrected in onebox_radar.c file.

Revision num 9943
   - Radar detection code optimization and improvised checks to avoid false radar detections.

Revision num 10022:
   - Usb compilation issue fixed. 

Revision num 10058:
  - Added checks to avoid tx command when TX is in progress in both zigbee and Bluetooth in PER mode.
  - Added some configuration checks for bt_tx and bt_rx commands in Application.
  - Added Coex mode variable in d_assets structure in common hal.

Revision num 10096:
  - Bug fix for mmc timeout interrupt in sdio.

Revision num 10128:
  - Bug fix for WLAN-1990, AP mode not working due to mmc0 timeout interrupt changes.

Revision num 10154:
  - Calling usb suspend after the receiving the done of sleep ack.
  - Not giving tx access to the protocols if ulp sleep ack is in queued state.
  - checking for scan state when power save timer expires and enables power save only when there is no scan in progress.

Revision num 10155:
  - Changed common_insert.sh to ensure that the clock speed module param is correctly picked.

Revision num 10169:
  - Corrected sdio clock setting via module params

  - Changed common_insert.sh to ensure that the clock speed module param is correctly picked.

Revision num 10177:
  - Multiple rx urbs for usb intf.
  - Changed tx and rx aggregation limit.

Revision num 10245:
  - Added NL80211 support for station mode.
  - Selection of NL80211 through menuconfig.

Revision num 10250:
   - Added debug print support for BT-LE commands.

Revision num 10336:
	- Support for AP mode through nl80211 interface.

Revision num 10339:
	- Optimization changes for AP mode through nl80211 interface.

Revision num 10342:
	- Hostapd compilation support through menuconfig
	- Resolved Compilation warnings for hogher kernel till 3.18

Revision num 10344:
	- WEP Shared bug fix through CFG80211.

Revision num 10345:
	- Compilation error fix for kernel 3.6.x versions and 3.7.x versions

Revision num 10352:
	- Compilation error fixes for kernels between 2.6.38 to 3.4.x.

Revision num 10354:
	- Compilation error fixes for kernels greater than 4.0.0.

Revision num 10356:
	- Sending VAP CAPS with update indication when there is a band change and channel width change.

Revision num 10359:
  - Returning SUCCESS in onebox_genlrecv function in BT PER mode.

Revision num 10383:
  - BT RF power mode input added as a module params .

Revision num 10390:
	- Changed TX and RX aggregation limits for increasing bidirectional throughputs.
	- Removed decrementing BE_Q aifsn value by -2.

Revision num 10391:
	- Written a function for killing URB's during suspend.

Revision num 10392:
	- Android changes - added get_rssi ioctl support.
	- Written a function for killing URB's during suspend.

Revision num 10395:
	- Added support for bluedroid stack in bt driver.

Revision num 10398:
  - Channel Utilization changes.
  - Handling of channel utilisation Stop command in sniffer mode.
	- Trilithic release changes 

Revision num 10416:
  - added callback events to cfg80211 interface.

Revision num 10444:
	- Bug fix for USB sniffer mode.
	- Inform recvd mgmt to cfg80211.
	- Added wrappers for p2p callbacks.

Revision num 10484
	- Modified Radar detection algorithm with pre-certification observations.

Revision num 10487
	- Added Configuration of the following for AP mode through CFG80211:
    	 20/40Mhz
    	 Short GI Configuration
    	 Hidden SSID
    	 ACL Policy

Revision num 10504
	- Compilation fixes for kernel version 3.14

Revision num 10529
	- Added support for 11d through cfg80211.

Revision num 10531
	- Added USB LP PS support without handshake.
	- Supplicant segmentation fault bug fix.
	- Trilithic stats bug fix.

Revision num 10580
	- DFS master support through cfg80211 supports for kernels greater than 3.9.0.

Revision num 10601
	- Fixed bug for creating virtual interface for kernels between 4.0 to 4.1.
	- Fixed crashes while delete virtual interfaces.
	- Added certs folder for EAP certificates.

Revision num 10602
	- Updated sta_settings.conf file for EAP methods.

Revision num 10609
	- Kernel compilation fixes for kernels upto 4.2

Revision num 10624 
	- Moved printks to Debug zone for WLAN.

Revision num 10631 
	- Not allowing ADDBA Setup until a node is Authorised, i.e, Will not accept addba request until Four way handshake is completed in security Modes.
	- Made printks enabled via zone
	- Upgraded to hostapd version 2.4
	- Updated .conf files for hostapd

Revision num 10637 
	- Compialtion fix for kernels between 3.16 to 3.18

Revision num 10660 
	- Bug fix for pings greater than 45000 in USB mode.
	- Crash fix with Nl80211 in AP mode.

Revision num 10663 
	- Driver hangup bug fix during wlan_insert.

Revision num 10679 
	- PER driver change for adding dc tone in cw mode.

Revision num 10720
	- Uncommented sending vap_caps in AP mode once vap state reaches RUN state.

Revision num 10725
	- A common function which take cares of deinitialisation of common hal related events for both USB and SDIO.

Revision num 10805:
	- ZIGB PER command number changes.

Revision num 10814:
	- AP Memleak bug fix.
	- Moving VAP state to INIT when we receive Deauth/Disassoc.
	- Dump stack bug Fix in AP mode.
	- Not performing any activity in INIT when requested state is of INIT state(Crash fix for AP mode during removal).
	- Added mic failure event indication to CFG80211.

Revision num 10819:
	- Changes in hostap conf files.
	- Bug fix for DFS channels.
	- Crash fix during removal of the driver.

Revision num 10917:
	- Bug fixes fod 11d, remove crash, soft lockup in AP mode
	- Updated hostapd conf files 

Revision num 10939:
	- Bug fixes that were committed in branch, pulled to trunk.
	- Including .config file in supplicant Makefile.

Revision num 10960:
	- Bug fix for chan flags, changed from HT to HT20

Revision num 10977:
	- Oper mode changes.

Revision num 10996:
	- Giving TX access to protocols when protocol card ready received.

Revision num 11006:
  - bug fix ZIGBEE end to end mode.

Revision num 11008:
	- Antenna diversity commits in the driver, added ioctl for selecting DFS channel to switch to in bsd mode.

Revision num 11013:
  - Disabling Power save for zigbee by default

Revision num 11052:
	- Sending delete notify when we get assoc req twice from STA.

Revision num 11082:
	- OPER MODE changes, and removed coex_mode from common_insert file.

Revision num 11188:
	- OPER MODE changes and renamed FW binaries.

Revision num 11216:
	- Made a Single binary for sniffer, end to end and PER mode.
	- Taking Protocols RF power mode values through Module Params.
	- Country Code through Module Params.

Revision num 11218:
	- Creating rpine0 bug fix for kernels > 3.17

Revision num 11220:
	- Added onebox_regdomain.h file to SVN.

Revision num 11231:
	- Added IOCTL for set rate with NL80211.
	- Changed OPER Mode to COEX Mode.
	- Added comments for RF Power Mode.

Revision num 11249:
	- Do not adding OFF channel Beacons to scan list if the recvd AP is not in the supported channels. 
	- Bug Fix for Sending Delete VAP in WIFI Direct Mode.
	- Initializing 14 channels in World region.

Revision num 11305:
	- Added IPV6 support
	- Bug fix for crash in WIFI Direct
	- Bug fix for dump stacks in common with ULP power save mode.

Revision num 11353:
	- Bug fix while removing wlan when power save is enabled. Unable to send deregister FW, AS module state is moved to removed state.

Revision num 11387:
	- Moved PONEBOX_ADAPTER to WLAN_ADAPTER.
	- Initialization of thread's and wait event variables related to thread_handle structure.

Revision num 11396:
	- Compilation error fixes and changes related to proc.

Revision num 11437:
	- Fixes related to bugs in P2P and monitor mode.

Revision num 11439:
	- Multiple Module changes.

Revision num 11441:
	- Changed the name common gpl to onebox_common_gpl

Revision num 11496:
	- Removed printk's, TODO's and FIXME's appropraitely.
	- Freeing pkt in BT BER.
	- Crash fixes for two modules.
	- Menuconfig changes.

Revision num 11531:
	- Removed Make files in subdirs.
	- Renamed .h files in protocols.

Revision num 11534:
	- Bug fix for Selective scan.

Revision num 11536:
	- Removed unnecessary Configurations in menuconfig.

Revision num 11568:
	- Removed PWD in make files.

Revision num 11600:
	- Fixes for compilation errors across kernels 2.6.35 to 4.2

Revision num 11601:
	- Decrementing 2 from BE_aifsn for both ap and sta if its value is greater than 2.

Revision num 11602:
	- Removed printing stats in creating vap ioctl.

Revision num 11603:
	- changed deault config in meuconfig to sdio and BSD

Revision num 11621:
	- Setting BIT(1) in frame_desc[1] for RF_3.3v.

Revision num 11636:
	- Changed the check conditions of mic failure in mic failure function.

Revision num 11638:
	- Bug fix of oper mode getting changed from BT_CLASSIC to WLAN_ALONE, when card is removed and inserted.

Revision num 11650: 
	- Bug fixes for crash during p2p_scan.
	- Modifying the usb_resume timer when tx_access is required for a protocol.

Revision num 11687: 
	- Removed rx thread incase of USB interface.
	- Crash Bug fix in autorate when 11g rates are only supported for connected AP.

Revision num 11709: 
	- Sending VAP Update in p2p Group owner once vap reaches Run state.
	- Bug fix of Belgium CTRY mapping to US.

Revision num 11758:
	- Compilation Error fixes for Android platforms.
	-	Memleak bug fixes in onebox_util and handling freeing of mgmt in failure cases.
	- Hardcoded remaining value to 20 in auto rate function.

Revision num 11759:
	- Keeping TA thread to Hold in reset card for USB interface.

Revision num 11785:
	- ZigBee CW mode changes.

Revision num 11786:
	- Added New feature BT-AFH in the bt-util.

Revision num 11810:
	- Removed compile option for USB and SDIO driver selection.
	- Added Configuring SDIO and USB interface support in menuconfig.
	- Bug fix of radar channels.

Revision num 11830:
	- Changes in Makefile not compile utils dir for Android.

Revision num 11898:
	- D-word alignment bug fix for internal mgmt and Dev config frame.
	- Bug fix for ignore case handling of mcs rates in transmit utility.

Revision num 11900:
	- Added support for station dump ioctl in NL80211.

Revision num 11906:
	- Bug fix in reading suspend time for USB interface. 

Revision num 11922:
	- Setting default rf_power_val to 1.9V. 

Revision num 11927:
	- Updated sniffer.sh script

Revision num 11942:
	- Removed curses.h from zb_transmit application.

Revision num 11948:
	- Ordered the prints into correct zones. By default, only ONEBOX_ZONE_ERROR is enabled, which logs only the error cases.

Revision num 12132:
	- ioctl's for enabling or disabling protocol. Wifi should be enabled mandatory in menuconfig to run any protocol.
	- Removed Debug Zone and SDIO Multiblock support in menuconfig.

Revision num 12152: 
	- Fix for compilation warnings on embedded platforms

Revision num 12180:
	- Added Support for CCX v1, v2 initial roaming. To enable CCX support enable RSI_CCX in config/make.config

Revision num 12338:
	- Bug fix in sending PER data frame. Adding direct to BE_STA_Q instead of sending through internal mgmt frame function.

Revision num 12350:
	- Bug fix for wlan enable and disable ioctl.

Revision num 12356:
	- Bug fix for crashes during enable and disabling of protocols.

Revision num 12360:
	- Dropping of RX packets has been added to avoid crashes when ever RX traffic is high. Pulled from 1.4.0 branch
	- Merged version and crash fix for ioctls issuing before WLAN FSM reaching MAC_INIT_DONE state.

Revision num 12363:
	- compilation error fixes

Revision num 12374:
	- Changed BT prints to related zones.

Revision num 12380:
	- Bug fix while removing driver without disabling BT and Zigbee protocols.
	- Removed wlan_insert.sh, bt_insert.sh, zigb_insert.sh script files.
	- Added scripts wlan_enable.sh, wlan_disable.sh, bt_enable.sh, bt_disable.sh,zigb_enable.sh,zigb_disable.sh for enabling required protocols.

Revision num 12382:
	- Updated scripts according to new changes.

Revision num 12436:
	- Changes for MFI.

Revision num 12437:
	- Added Wacposix server application for wac.

Revision num 12441:
	- Pulled in bug fix for disable protocol ioctl not working in cfg80211.

Revision num 12504:
	- Makefile changes to compile the driver from any path.
	- Fixed compilation warnings in onrbox_util.c

Revision num 12530:
	- Bug fix zigbee warning during netdev registration.
	- Removed Handling of packets less than 16 bytes in onebox_rx_done_handler function.

Revision num 12567:
	- Bug fix during removal of wlan driver. Not calling unregister_netdev when reg_state is not in NETREG_REGISTERED.
	- wait_for_completion is removed for kernels > 2.6.39. This is handled by kthread_stop.
	- Commented releasing of ipaddress in WAC when PlatformMFiAuthFinalize is called. 

Revision num 12585:
	- 11W changes.

Revision num 12667:
	- Not allowing bgscan active scan and passive duration greater than 255.

Revision num 12774:
	- Avoiding recompilation of all files.

Revision num 12821:
	- Kernel compilation error fix for kernel < 3.2.0.
	- Not allowing reset adapter when multiple vaps are created.
	- Handling of error cases for enable protocol.

Revision num 12822:
    - 9116 buffer read/write changes

Revision num 12879:
    - Flashing changes for 9116

Revision num 12882:
    - fixed an error in upgrade.sh

Revision num 13067:
    - bt_utils and zigb_utils cleanup

Revision num 13865:
		- Updated onebox_radar.c according to the latest Certification.Merged from Golden database

Revision num 13909:
    - merged radar automation changes.

Revision num 13945:
    - 11AH PER changes

Revision num 14333:
    - JHELUM Bug fixes { 3669, 5262, 5263}

Revision num 14383:
    - Merging golden branch changes to trunk { WAC related issues, BT crash fixes}

Revision num 14426:
    - Merging goldein branch changes to trunk {11J, CCX, bug fixes done on golden branch}

Revision num 15021:
		- Bug fix for crash while running BT BER curve.		

Revision num 15027:
    - 9116 bootloader changes

Revision num 15460:
		- BT PER STATS Bug fix in matlab_utils.c

Revision num 16086:
		- Added support for loading firmware through bootloader for 9116

Revision num 16419:
		- Added support for Direct and indirect addressing buffer writes through
			matlab
Revision num 16585:
	   Merged 9113 branch chages to trunk

Revision num 16632:
	- WLAN-3331 Licensing changes in onebox driver.

Revision num 16655:
	- [JHELUM -7583] - Fixed  crash issue with the print_station_stats command in onebox_util.
	- [WLAN-5112] - Missing information in iw link command

Revision num 16799:
        - Fix for trunk driver not working in 9116.

Revision num 16883:
	-[WLAN-3449]/ [CE-5288] Crashes observed due to invalid use of memcpy from userspace to kernel space in ioctl path
	- Bug fixes for WLAN-3270 & JHELUM-6977
	- Bug fixes for WLAN-3483, CE-5246
	- BT feature bitmap  added
	- Bug fix for WLAN-3491
	- Return error if STA/AP is started when not configured in COEX_MODE in common_inser.sh
Revision num 17204:
        - [JHELUM-7239] - Bug fix for the IAP CHIP INITIALIZATION.

Revision num 17270:
	- Return error if STA/AP is started when not configured in COEX_MODE in
		common_inser.sh
	- Removed unwanted prints and error check in add_appie in
		ieee80211_output.c
	- Added a define RSI_CCX in onebox_core_vap.c to avoid compilation error
	- There was a bug in the RADAR detection algorithm, in regard to calculating
		the average of pulses, fixed it. 
	- Copy_to_user function must be called only in WRITE case in
		onebox_iap_config. Rectified it. 
	- Included TESLA concurrent mode changes in the Golden base. 
	- Rejecting pulses less than 100us in onebox_radar.c
	- Checking data_buffer_full status instead of mgmt_buffer_full for Multicast
		packets to make sure beacons are not blocked. Bug ID WLAN-3536

Revision num 17321
	-	Updated the Max TX powers in in all regulatory domains to 24, This is the
		max tx power of redpine module keeping HPM in mind. Bug ID CE-5529 
	- Buf fix for iwconfig up/down iteration. sending scan done notification to
		cfg80211 layer. Bug no: CE-5428

Revision num 17496
	- TESLA concurrent mode bug fixes
	- Trilithic changes in trunk
	- tx power in AP bug fix

Revision num 17626
	- Fixed Bug no WLAN-3597

Revision num 18151
	- Fix for CE-5437 (Kernel crash while issuing vap_stats ioctl)
	- Densowave - During interface up/down removing of initialised work-queues in supplicant
	- Fixes for JH-8303, JH-8176, WLAN-3721, WLAN-3532

Revision num 18952
	- In AP mode, before connection, the rate is shown as 1mbps in 5G. Rectified
		it, CE-5580
	- Removed 14 channel support in World Domain, WLAN-3690
	- Ioctl option to enable/disable 802.11h support - CE-5866
	- Added PS enable/disable support for nl80211 interface, Fix for CE-5719
	- Changes for enabling config_peer distance support through module params.
	- Fix for WLAN-3750 - Add 11n rates support in 11j mode for PER mode.
	- Max power enable ioctl for Mitsubishi
	- Redpine STA unable to connect to multiple ESSID AP, when sta driver is
		removed and inserted again. CE-6012
	- Added Max power ioctl for PER mode as well.

Revision num 19027
	- Implementation for PS control from cfg80211. BugID CE-5719
	- 40Mhz bug fix in ieee80211_node.c

Revision num 19659
	- Added Nokia Spectral mask changes, including 3 new files, flash_write.sh,
		common_insert_flash.sh append_pwr_values.c
	- Added Redpine copyright statement in all the files [WLAN-3762].
	- Bug fix for WLAN-3764 ( Crash in AP mode during automation)
	- Bug fix for CE-5763- Monitor mode support with Nl80211 interface
	- Bug fix for CE-6062 Concurrent mode support with Nl80211 

Revision num 20036
	- Fix for CE-5389 [Kernel panic when n/w manager is enabled.]
    NULL pointer/state is added in ioctl path.
	- JHELUM-9133 Fix for BT/BLE driver to work.

Revision num 20307
	- Auto channel selection in AP mode using Hostapd.

Revision num 20365
	- Tesla patches added to mainline including onebox_util changes.
	- Bug fix for CE-5678 (RS9113 not able to send in 150mbps rate)
	- Bug fix for WLAN-3874, WLAN-3885, WLAN-3886, WLAN-3816, WLAN-3875.

Revision num 44981
	- ACS changes in set_channel() added

Revision num 45141
	- Vantage robotics Use only rates ioctl changes (CE-6002)

Revision num 45175
	- Memory leak in AP mode CE-6489 

Revision num 45678
	- Memory leak fixes {CE-6574}
	- 40Mhz fixes [WLAN-3978]
	- Fix for compilation error in lower kernels [WLAN-3976]	 

Revision num 46454
	- iwconfig fixes, corrected jointime, rssi, txrate in print_sta_info ioctl

Revision num 46683
	- Fix for WLAN-4016, WLAN-4008

Revision num 46991
	- Fix for CE-6776 (Support on higher kernels >= 4.10.x)
	- Usb control msg (input buf memory is dynamically allocated")
	- Support for higher kernel[upto 4.12] added with NL80211 interface.

Revision num 47254
	- Fix for WLAN-4024 (Implementation need to be done for the following ioctls)
	- Fix for WLAN-4069 (Supported Rates are Null in P2P Probe Responses in BSD)

Revision num 47256
	- Fix for WLAN-4023(Unable to create AP in DFS channel using NL80211 interface)
	- Fix for WLAN-4012 (11b only rates should go in JP region CH-14)

Revision num 47361 
	- Fix for WLAN-3909(signal strength not shown in iwconfig at AP side)
	- Fix for WLAN-4029 (Observed card read failures while removing the driver)

Revision num 47919
	- Added support for ble_aoa_aod transmit and receive in PER.

Revision num 47939
	- Fix for CE-6883 (Configuration to set sta keep alive via ioctl).
	- Fix for CE-6884 (Regulatory max power setting changes).
	- Fix for CE-6995 (Unable to read tx/rx bytes)

Revision num 47940
	- Fix for wlan-4117 {support for kernel version < 3.15.x}for Nl80211 changes
	- Fix for wlan-4122 {connectivity issue with the fix wlan-4023}

Revision num 48330
	- Fix for CE-7113 (Crash while running AP mode)

Revision num 48394
	- Fix for WLAN-4117 (Observed keep-alive timer is not changing with ioctl command)
	- Fix for WLAN-4187 (Wrong MFG version handling in Driver) - Crucible (CR-521)

Revision num 48437
	- Fix for CE-6873 (BT firmware is not active" in validation of RS9113.NBZ.NL.GENR.LNX.1.5.2 (continuation of old support system ticket 6184))

Revision num 48438
	- Updated Release Notes

Revision num 48451
	- Fix for WLAN-4207 (Compilation issues in 1.5.6_RC3) 

Revision num 48466
	- Fix for WLAN-4209 ([QA-9113-1.5.6]Observed LP powersave is auto enabled when connected to 3rd party AP's in NL mode) - Crucible (CR-536)
	- Fix for WLAN-4210 ([QA-WLAN-1.5.6]Observed keep_alive (8BE0): Operation not supported while issuing keep-alive ioctl in AP mode) - Crucible (CR-536)
	- Fix for WLAN-4211 ([QA-WLAN-1.5.6-RC4] Observed auto channel slection feature is not working) - Crucible (CR-536)
	- Changed Zone Enabled flag from 0x50013 to 0x1
	- Correction in  Kernel Version Check

Revision num 48467
	- Updated drv_release_notes for correct SVN Revision

Revision num 48479
	- Fix for WLAN-4216 ([QA-WLAN-1.5.6]Observed UAPSD powersave is unable to set with the given command)

Revision num 48480
	- Wrongly commited files changed

Revision num 48481
	- Kernel Version udpated as per Kernel Std

Revision num 48601
	- Fix for CE-7184(Reset because of memomry leak?[Densowave])

Revision num 48620
	- P2P support added for NL80211

Revision num 48646
	- WoWlan Support added for NL80211
	- SDIO suspend and resume support added

Revision num 48674
	- Fix for CE-6953 (2 days later, RS9113 does not respond [Densowave] Lennox n-Link)

Revision num 48699 
	- Adding a separate common_insert.sh for RS9116 SoC.

Revision num 48700
	- Adding a separate common_insert.sh for RS9113 SoC.

Revision num 48704 
	- Default values for RS9116.

Revision num 48713
	- Adding driver version mechanism for multiple SoCs.

Revision num 48778
	- Fix for RSC-801 ([n-link-9116-QA-WLAN]Unable to compile NL mode in 3.6.10 kernel on 64-bit device)

Revision num 48781
	- Fix for Wlan-4239 (Short_Gi not disabled while taking AP alone throughputs in 5GHZ because of this throughput getting less.)

Revision num 48783
	- Fix for WLAN-4213 (Value validation handling in driver for antenna select ioctl)

Revision num 48894
	- Fix for WLAN-4184 ([QA-WLAN-1.5.6_RC2] Unable to set tx_power through ioctl in STA mode.)
	- Fix for WLAN-4239 (Observed less throughput in AP alone 5 Ghz mode as Short GI is not disabled.)
	- Removed BT BLE PER Mode Binaries meant for 9116 while cleaning driver.
	- Removed unwanted printk

Revision num 48967
	- Fix for WLAN-4200 ([QA-WLAN-1.5.6]Observed onebox ioctls are not accepted when multiple modules are connected to host)

Revision num 49103
	- Fix for WPA2_KRAK
	- Fix for compilation issue on 2.6.30 Kernel

Revision num 49139
	- Fix for WPA2 KRAK for BSD Interface in supplicant and host driver

Revision num 49321
	- Fix for Wlan-4294 [QA-1.6.0_RC1] SAM9G45:Nlink Observed compilation error while compiling given host.

Revision num 49380
	- Big Endian Support Added

Revision num 49382
	- Fix for WLAN-4345 Handling of rate of control packets in 5Ghz mode in AP mode

Revision num 49384
	- Fix for Android Compilation Issues

Revision num 49395
	- Fix for WLAN-4342 [n-Link_QA_1.6.0_RC2] Observed error in the driver compilation for nl80211 in 3.3 kernel 

Revision num 49521
	- Fix for WLAN-4323 [QA-WLAN-1.6.0_RC2]Observed AIFSN value is not changing in beacon in Apmode. 

Revision num 49532
	- Fix for WLAN-4323 Observed WIFI STA got dissconnect due to Bmiss in 40Mhz

Revision num 49532
	- RS9116 boot up params enhancements.

Revision num 49553
	- Merging development branch to trunk for taking RS9113-RS9116 compatible tag.

Revision num 49613
  - Fix for  CE-7638 is there a way to query the flash type?
  - Fix for [nLink-QA-1.6.0] Observed driver is getting hang while running hostapd in AP mode.

Revision num 50197
	- CR-811 RF Selection Changes for the BT RF Type for the 9116 chip.

Revision num 50243
	- RF Type Extraction in the onebox_insert script.

Revision num 50427
	- Fix for CE-7581 How to operate RS9113 for WEP shared/open[DENSOWAVE]

Revision num 50445
	- All SDIO specific code should be under USE_SDIO_INTF. SDIO_COMMANDS flag should be under USE_SDIO_INTF. These changes resolve SDIO specific issues reported by USB customer(Nokia)

Revision num 50485
	- Resolves Densowave fastpsp disable failure issue(CE-7758)

Revision num 50486
	- Resolves Densowave issue "Station keeps on scanning and consumes more power when it is trying to connect to AP with wrong password" (CE-7859)

Revision num 50525
	- Added support for wlan feature frame ioctl to work before enabling protocol and enabled End of frame feature indication.

Revision num 50692
  - Added support for module params selection for 9116 specific features #RSC-1318 #CR-855 #CR-856

Revision num 50693
  - Added support for module params selection for 9116 specific features #RSC-1318 #CR-855 #CR-856

Revision num 50736
  - Resolved NULL pointer dereference when software bootloader is upgraded. #CR874 #WLAN-4428

Revision num 50785
  - Fix IOCTL implementation for 4.12 and higher kernels #CR-882

Revision num 50841
  - #CR-911, #RSC-1313 : Added bmiss timeout based on dtim and beacon interval.
  - #CR-900, #RSC-1328 : In connected state on receiving bgscan complete event
    from firmware, disabling scan.

Revision num 50970
	CR-932 - Host driver fix for the STA connectivity failure in concurrent mode.

Revision num 50972
	Resolve compilation errors observed while enabling 11w config in supplicant #CR-872 #RSC-1305

Revision num 50998
	Fix kernel crash by replacing memcpy with copy_from_user #CR-945 #RSC-1418

Revision num 51000
	Fix compilation issue caused due to #CR-882

Revision num 51035
	Add compile time option for Barco to disable DFS channels #CR880 CE-7534

Revision num 51090
	Add compile time option for Barco to disable DFS channels #CR880 CE-7534	
Revision num 51209
	Fix memory leak in USB path #CR998
Revision num 51230
	Error core handling correction for BT #CR995

Revision num 51231
	802.11K support for 6 parameters #CR582

Revision num 51233
	Fix for zero noise floor value in hostapd logs #CR915 #RSC1273

Revision num 51400
	Remove redundant 64 bit alignment  #CR-990

Revision num 51441
	Resolve 'AP stays in encryption mode' issue #CR-982 #CE-8081

Revision num 51533
	Add antenna select command in sniffer mode #CR1030

Revision num 51533
	RSC-1747 : We should not be using GFP_DMA. Kernel documentation says "GFP_DMA exists for historical reasons and should be avoided where possible."

Revision num 51621
	RSC-1705 : Proper handling for sleep type transition.

Revision num 51677
	Fix compilation issue for higher kernel #CR1057

Revision num 51680
	Cumulative fixes for multiple RS9113 modules scenario #CR1056

Revision num 51681
	btgenl registration only in EVAL mode #CR1082
	
Revision num 51760
	Added RS9116 BLE config options.

Revision num 51782
	RSC-1760 Fix.

Revision num 51787
	CR-1005 : Following proper coding guideline for w_9116_features_t for all platforms.

Revision num 51860
	Updated the BT-PER IOCTLs as per the new f/w changes.

Revision num 51891
	UAPSD service period length configuration support. Resolve compilation error in pre-committed code #CR-1105

Revision num 51903
	RSC-1888, CR-1121 - Added DS Parameter set in probe request in 2GHZ scanning.

Revision num 51907
	RSC-1953 - Observed error handling is not present while creating wrong vap in Station and AP 
	modes. As part CR-882 each ioctl is returning always 0. This is corrected 
	now to return proper value.

Revision num 51912
	Add Tx packet life time value module parameter #CR1123

Revision num 51913
	Resolve beacon miss indication takes ~50seconds on ARM platform issue #CR1117

Revision num 51914
	RSC-1935 Invalid rate index received from FW print while running 40MHz [CR-1116]

Revision num 51927
	Added support for 11R over the air #CR-1112

Revision num 51928
	Some of the code was not guarded with ENABLE_P2P_SUPPORT. Hence disabling the flag was causing some issue. This patch addresses the issue. CR791 WLAN4364

Revision num 51929
	Change CONFIG_TXPKT_LIFETIME value to 0. #CR-1123

Revision num 51946
	Resolve compilation issue with 4.0 kernel #CR1136

Revision num 52024
	Fix compilation errors on higher kernel. These are warnings for lower kernels. CR#1145

Revision num 52025
	Disable CCX flag, as it gives garbage scan results. CR#1146	

Revision num 52056
	Making the device name as generic RS91xx for all the chips.	

Revision num 52057
	Memory Leak Fixes for BT and common FW load #CR993

Revision num 52156
	Race condition handling in AP mode CR#1006 

Revision num 52164
	WLAN-4559 & CR-1153.

Revision num 52165
	Ticks/jiffies handling in the driver CR#1130

Revision num 52171
	Fix ioctl issue with BSD on higher kernels #CR1159

Revision num 52211
	Disabling GTK rekeying offload feature by default.

Revision num 52212
	Receive stop doesn't work in PER Mode test cases CR#1127 CE#8237

Revision num 52213
	Resolve issue observed during hostapd configuration change from 20Mhz to 40Mhz CE#8006 CR#950

Revision num 52214
	11R over the DS feature support changes CR#963

Revision num 52226
	Resolve compilation issues introduced by rev 52213

Revision num 52227
  #CR-597 PUF related host driver changes. Default feature is disabled

Revision num 52248
	Minor change to correct function name #CR1159

Revision num 52249
	[MATLAB UTILS] Error case handling in read_stats function CR1143, CR1179

Revision num 52250
	Change 9113 release version from 1.6.0 to 1.6.1

Revision num 52270
	Resolve compilation issues when ACS is enabled in 4.8.6 kernel WLAN-4480 CR-889

Revision num 52301
	Added rpineX option to PER commands. This will help when multiple modules are connected to same host. CR#1126

Revision num 52386
    Added Connection monitor events for BG-SCAN and Roaming for NL80211 Driver. #RSC-2032,#CR-1192.

Revision num 52433
    Resolve 11R related compilation issues on lower kernels #CR-1220 #WLAN-4588

Revision num 52459
    Resolved crash issue observed during BT PER testing. Reverted some of the improvements in CR-993 which caused crash

Revision num 52463 
    Default Firmware loading is "WITHOUT Secondary Boot Loader with Scatters(FW_LOAD_MODE=5)" if device model is 9116. RSC-2244, CR-1225.

Revision num 52526
    Clear group key in AP mode after killing wpa_supplicant/hostapd #CR1229 #CE8278

Revision num 52569
    Remove incorrect error handling for transmit_pkt(). This change resolves 'ifconfig showing packet error issue' #CE8311 #CR1191

Revision num 52577
    Restrict max SSIDs received from wpa_supplicant to 3 in driver #CR1111

Revision num 52579
    Updating driver version for RS9116.

Revision num 52767
    Fixed Memory leak issue while inserting and removing driver.

Revision num 52774
    Resolve AP sending deauth issue in concurrent mode when station interface is down #CR1250 #WLAN4614

Revision num 52775
    Resolve Per receive doesn't start for first time, after running one iteration problem #CR1244

Revision num 52776
    Some part of 11R over air code is defined under RSI_CCX flags which breaks 11R in latest code. Resolve the problem by making it available for CONFIG_11R also #1241

Revision num 52836
   Resolve kernel crash observed while deleting vap in AP mode(hostapd is running) #CR1252 #WLAN4600

Revision num 52841
   Resolve compilation errors on lower kernels(introduced after adding recent RSSI based roaming support) #CR1256 #WLAN4622

Revision num 52879
   Advertise DFS and passive scan flags for DFS channels. #CR1266

Revision num 53095
   RSC-2357.
   CR-1283 : Fix for kernel crash during removing driver in hostapd & running 
   iwconfig in background.

Revision num 53096
   CR-1289 : Fix for Memory leak in NL80211 interface.

Revision num 53111
   CR-1301 : Fix for memory leak during driver insert/remove regression testing.

Revision num 53139
   CR-1301 : Changing RS9116 driver version no.

Revision num 53143
   CR-1302 : Handling crash due to invalid pointer access in rmmod path

Revision num 53144
   CR-1287 : Clearing group key when wpa_supplicant/hostapd is killed

Revision num 53182
   CR-1304 : Resolved frequent beacon miss indications in iMX6 platform. iv_swbmiss_period should
	     hold value in msecs. This issue was introduced while merging CR#1130 to SVN code

Revision num 53186
   CR-1289 : Resolve memory leak observed during load/unload stress test

Revision num 53237
   CR-1318 : Added Tx power error conditions as per the latest power programming changes.
   http://192.168.1.215:8090/display/RF2GGF40/Transmitter+and+Receiver+Gain+Tables#TransmitterandReceiverGainTables-LPChain(Both0dBmand10dBm).

Revision num 53257
   CR-1085 : 802.11W Driver Bug Fixes.

Revision num 53302
   Added New BT-9116 Parameters in the wlan_bt_insert.sh script.

Revision num 53319
   RSC-2499 : Fix for seciruty mode failure in RSI_AP in 4.10 kernel.

Revision num 53335
   WLAN-4612, CR-1286 : SAM9G45, Unable to compile the driver for SAM9 platform.

Revision num 53369
   Added Default Parameters for the BT/BLE LP Chain Tx power and Power Save options.

Revision num 53393
   CR-1348 : FIx for handling onebox_util ioctl like print_vap_stats,print_station_stats, 
   print_station_info.

Revision num 53406
   RSC-2429 : BT+WLAN STA throughputs
   CR-1362  : Increased max onair tx packets to be aggregated.

Revision num 53407
   RSC-2227, CR-1292 : Internal driver validation with 4.15 kernel.

Revision num 53485
   CR-1397 : To display rssi value of connected station in AP mode using command "iw dev station dump".

Revision num 53503
   CR-1401 : While we are switching VAP mode for P2P GO unblock beacon interrupts.

Revision num 53552
   RSC-2540, CR-1412 : Driver hang while connecting station in AP+BT+BLE mode.

Revision num 53653
   RSC-2514 : Observed deep sleep is not working in SDIO interface on Wand platform.
   CR-1421  : Fix for ULP enable driver removal and Memory leak.

Revision num 53688
   WLAN-4723 & CR-1432 : iwconfig shows 0dBm in the signal level field.

Revision num 53688
   WLAN-4622 : Latest Driver code is having compilation errors.

Revision num 53688
   CR-1421 : Cleaning identifiers in driver which are similar in driver & hostapd

Revision num 53688
   CR-1445 : Remove warning of truncating value of a kmalloc flags.

Revision num 53688
   CR-1421 : Fixing few complilation errors in cleaning identifiers in driver which are similar in driver & 
   hostapd.

Revision num 53975
	CR-1485 : Fix for BT firmware is not active in after some enable and disable 
	sequences.

Revision num 53975
	CR-1476 : Observed showing frequency 5080 in iwconfig ,while scanning in 2.4GHZ in jp 
	region.

Revision num 54090
	CR-1476 : Observed showing frequency 5080 in iwconfig ,while scanning in 2.4GHZ in jp 
	region. This is some more optimizations over last changes.

Revision num 54091
	CR-1502 : Updating Hard coded path of DHCP server script in supplicant.

Revision num 54436
	Fix for the RS9116 BT/BLE Transmit from the matlab utils.

Revision num 54443
	Fix for #RSC-2798 : Increased 9116_Max_AMPDU_RX to 16k from 8k & TX PKT Aggregation to 12 from 8.

Revision num 54444
  	#RSC-3060 #CR-1587 - Added support for selecting sleep clock in common_insert.sh.

Revision num 54623
	#RSC-2798 Increased 9116_Max_AMPDU_RX to 16k from 8k.TX PKT Aggregation to 12 from 8.
	#WLAN-4674 #CR-1420  Fix for ACS with DFS channel (5Ghz) not working issue.
	#CR-1472  changes for iwpriv command to change channel using CSA.
	#WLAN4696 #CR-1473  changes for handling segmentation fault during VAP delete.
	#RSC-2786 #CR-1528 fix for accessing wrong hal_vap offset.
	#CR-1579  Fix for compilation warnings while compiling propreitary driver in kernel versions between 4.14.12 to 4.17
	#CR-1590  Removing aggregation in AP TX, if connected STA is in power save (Disabled by default)
	#RSC-3128 #CR-1630  Changes done in wlan_bt_insert.sh script to load module in Coex mode. 
	#CR-1631  Changes for Taking Beacon Interval from hostapd conf file.
	#CR-1632  Changes to start Netdev queues after completing CSA/Quite element time in STA mode.
	#RSC-3149 #CR-1647  Changes for Help in Driver Menu_Config.

Revision num 54684
	#CR-1628 Added Suport for the configuration of the slaves in the Hosted Mode.

Revision num 54784
	#RSC-3407 #CR-1703 Fixed Kernel crash in AP mode Enable path

Revision num 54913
	#RSC-3495 #CR-1723 Fixed Group key TX packet's wrong offset access while updating retry count and queuing to head

Revision num 55111
	#RSC-2870, #CR-1788 Packet Error Rate Support Changes in the receive utils.

Revision num 55125
	#RSC-3410 #CR-1713 Fixed Compilation warnings upto kernel versions 4.17

Revision num 55144
	#RSC-3615 #CR-1792 Fixed compilation error in compiling Driver for 11W

Revision num 55166
	#RSC-3629 #CR-1803 Fix for card read failure in SDIO+ULP case
	
Revision num 55180
	#RSC-2877 #CR-1801 Added receive stats percentage calculation in PER utils
	
Revision num 55186
	#WLAN-4877 #CR-1753 Fixed wrong TX rate & TX power in station dump and Beacon miss handling in P2P.
	#RSC-3614 #CR-1812 Removed limiting country domains according to module_type for 9116.	

Revision num 55196
	#RSC-3708 #CR-1825 Added Configurability for BDR mode from driver.

Revision num 55269
	Updated version number and reverted r55210 changes as that fix need to handle Concurrent mode/Multiple VAP cases.

Revision num 55274
	#RSC-3673 #CR-1836 Fixed deadlock in WLAN Disable protocol.
 	
Revision num 55275
	#RSC-3467 #CR-1844 Fixed Kernel Crash issue while AP remove_all.
	
Revision num 55286
	#RSC-3487 & #RSC-3488 #CR-1780 Fixed 11R mode roaming and bgscan issues.
	#RSC-2170 #CR-1843 Changes in 11W 
	1. Resolved improper handling of SA Query procedure in AP mode.
	2. Resolved improper handling of Association request in 11W AP mode.
	3. Added Buffering mgmt packets along with data packets in AP mode when connected STA is in power-save.

Revision num 55295
	#JHELUM-1036 #CR-1854 Fixed system hang while issuing RF write/read IOCTL in SDIO mode.

Revision num 55295
	#RSC-3776 #CR-1853 Fixed error while inserting driver in 4.14 kernel. 

Revision num 55309
	#RSC-2170 #CR-1843 Updated unrequired TIM update in 11W and removed packet dump.	

Revision num 55311
	#CE-9040 #CR-1833 Added saving roaming feilds in conf file and Fixed bsd case roaming.

Revision num 55323
	#CE-9157 #CR-1830 Added Changes for Big Endian platform.

Revision num 55331
	#CE-8859 #CR-1778 Changed structure attribute to fix issue with ARM GCC compiler 3.4.1.	

Revision num 55410
	Updated Driver Version to 1.0.a

Revision num 55426
	#RSC-3827 #CR-1883 Added common insert entry for three_wire_coextsence.
	
Revision num 55472
	#RSC-3835 #CR-1886 Fixed driver compilation error for linux kernel v3.19. 

Revision num 55514
	#RSC-3844 #CR-1893 Fixed Memleak in AP mode driver removal path,when at least a station is connected.

Revision num 55527
	#RSC-3859 #CR-1902 Added showing power save info for iw_get_power_save command even PS is enabled through onebox_util. 

Revision num 55539
	Updated driver version to 1.0.b

Revision num 55637
	#RSC-3343 #CR-1910 Added common insert entry for ANCHOR_POINT_GAP.

Revision num 55642
	#RSC-3777 #RSC-3808 #CR-1929 11K define and Multicast changes.

Revision num 55646
	#RSC-3846 #CR-1928 Added fix to send ADDBA only if HT&WMM ie's are existed in ASSOC REQ/RESP.	

Revision num 55711
	#RSC-1611 #CR-1868 Added bigendian support for 9116 code.

Revision num 55717
	#RSC-3868 #CR-1925 Added 11J channels scanning support to NL mode.
	
Revision num 55726
	Updated driver version to 1.0.c.

Revision num 55769
	#CE-8872 #CR-1914 Fix for random call trace while data transfer.	

Revision num 55851
	#RSC-3858 #CR-1954 Fix for USB card read failures with connect/disconnect script.
	
Revision num 55855
	#CE-8773 #CR-1912 Added dropping packets with TID greater than 8.

Revision num 55859
	#RSC-3886 #CR-1963 Fix for RSI_STA fail in 40Mhz with TP-link AC750 AP.

Revision num 55862
	#CE-9208 #CR-1948 Added fix for Active scanning in DFS channels.

Revision num 55885
	#RSC-2452 #CR-1898 Added Country code configuring from hostapd and supplicant in NL80211.

Revision num 55887
	Updated driver version to 1.0.d.

Revision num 55888
	#RSC-2452 #CR-1898 Added country configuration in sta_settings file.

Revision num 55933
	#RSC-3957 #CR-1958 Fix for handling firmware assert 0xa.

Revision num 55955
	Updated driver version to 1.0.e.

Revision num 55992
	#RSC-4005 #CR-1977 Fix to print packet dump in single line from kernels 4.9 and above.

Revision num 55008
	Updated driver version to 1.0.f.

Revision num 56055.
	Updated driver version to 1.0.g.
	
Revision num 56072.
	Updated driver version to 1.0.0.

Revision num 56091.
	#CE-9301 #CR-2002 Added changes to deferentiate ACS scan and HT40 scan and handle them differently. 

Revision num 56093.
	#CE-9301 #CR-1917 Added changes for complete clean up of AP flags on receving stop ap from hostapd.

Revision num 56094.
	#CE-9023 #CR-1834 Added changes in declaration of timer variables for proper handling of 64bit values.

Revision num 56112.
	#RSC-4096 #CR-2015 Fixed kernel crash in ULP power save.

Revision num 56114.
	#CE-8941 #CR-1913 Fixed AP mode bandwidth switch issue in 5G mode.	

Revision num 56115.
	#Reverted 56090 revison (fix #RSC-3942 #CR-1987) as side effects are observed.

Revision num 56154.
	#Differentiated user and developer/debug configurations in common_insert.sh file.

Revision num 56172.
	#RSC-4006 #CR-1979 Added ONEBOX_DEBUG prints in place of printk in cfg80211_wrapper.c file.

Revision num 56173.
	#RSC-323 #CR-1911 Added fix to remove unnecessary error messages while insert and removal.

Revision num 56174.
	#RSC-3930 #CR-1947 Added fix for compilation error in 2.6.38 kernel in NL mode.	

Revision num 56233.
	Updated driver version to 1.0.2.

Revision num 56329.
	Updated driver version to 1.0.3.

Revision num 56353.
	#RSC-4147 #CR-2049 Added API for Zigbee end device start.	

Revision num 56355.
	#RSC-4160 #CR-2034 Removed support for dynamic change of ssid and channel through iwconfig ioctl call.	

Revision num 56361.
	#CE-9478 #CR-2031 Added changes for stopping timeout handler in VAP delete. 

Revision num 56371.
	#WLAN-4697 #CR-2011 Added changes for memory leak in driver with ni pointer.	

Revision num 56402.
	#RSC-3829 #WLAN-4955 #WLAN-4954 #CR-2058 Fixed packet drops in driver, reduced queue depths and added multiple TX queues.	

Revision num 56455.
	#WLAN-4952 #CR-2064 Added changes to bringup zigbee coordinator & router in RS-9116.

Revision num 56463.
	#WLAN-4956 #CR-1615 Added changes for Sending Max AMPDU size support in Peer Notify	

Revision num 56478.
	#WLAN-4956 #CR-2071 Added changes to update Tx Aggregation value to LMAC.	

Revision num 56495.
	#CE-9539 #CR-2086 Added changes in debug level of Radar Specific prints.

Revision num 56495.
	#CE-9464 #CR-2097 Added changes for more data offsets in Data Packet Desc for Big Endian.

Revision num 56450.
	#RSC-4194 #CR-2079 Added changes for handling hostscan_2g command.	

Revision num 56514.
	#RSC-4261 #CR-2087 Added fix for more time to FW load issue on USB inteface on wandboard.	

Revision num 56530.
	#RSC-4378 #CR-2105 Added fix for host_scan ioctl failure.

Revision num 56541.
	#CR-2110 Version number change to 4digit from 3 digit to support CE patch version numbers.

Revision num 56680.
	#RSC-4324 #CR-2120 Added fix for 'RSI_STA sending disasoc to AP while doing normal roaming in security modes'.

Revision num 56682.
	#RSC-4390 #CR-2119 Added fix for Bgscan is getting stopped while running data transfer when 11R is enabled.

Revision num 56709.
	#RSC-4390 #CR-2119 Added modification in fix for Bgscan is getting stopped while running data transfer when 11R is enabled.

Revision num 56716.
	#RSC-4382 #CR-2122 Added timer_setup API for timer initialization for Linux kernel above 4.15.

Revision num 56736.
	Updated driver version to 1.0.5.0.	

Revision num 56747.
	Updated driver version to 1.0.5a.0.	

Revision num 56821.
	Updated driver version to 1.0.5b.0.	

Revision num 56829.
	#RSC-4348 #CR-2125 Fixed card ready failure issue for 2nd time insert on ultralite platform.

Revision num 56851.
	#JHELUM-10482 #CR-2117 Added changes (for Manufacturing firmware) to support Receiver mode based on GPIO/host handshake via Matlab interface.

Revision num 56891.
	#Disabled r56371 commit changes as BG scan is failing. 

Revision num 56940.
	#CR-2155 Added reserved bit for bt classic per structure to compensate alignment in Firmware.

Revision num 56942.
	#RSC-4484 #CR-2152 Changes to not update Tx power levels in AP mode in ACS.

Revision num 56961.
	#RSC-4204 #CR-2102 Added DFS master support for NL80211 inerface.

Revision num 57038.
	#CR-2153 Added fix for removing Warnings while compiling utils.

Revision num 57080.
	#RSC-4605 #RSC-4606 #CR-2174 Disabled set_mode and get_mode private ioctls as they are obsolete.

Revision num 57153.
	#RSC-4555 #CR-2193 Upgraded Driver Kernel support to the kernel v4.19.1. 

Revision num 57169.
	#RSC-4347 #CR-2103 Fixed BT power save issue after WLAN disable in coex.

Revision num 57171.
	#RSC-4469 #CR-2182 Fixed 5G disconnection issue due to country update after connection.

Revision num 57175.
	#RSC-4551 #CR-2158 Fixed IEEE80211_LOCK_ASSERT macro and other lock issues. 

Revision num 57193.
	#RSC-4341 #CR-2098 Fixed Card write failure while running AP and STA modes.

Revision num 57195.
	#RSC-4551 #CR-2195 Fixed lock assert issue in beacon miss algorithm.	

Revision num 57207.
	#RSC-4667 #CR-2194 Added input limits for the power save ioctl.

Revision num 57320.
	#RSC-4661 #CR-2205 Fixed running RSI AP mode with 5G channel 8.

Revision num 57328.
	#Updated Driver release version number to 1.0.6.

Revision num 57331.
	#RSC-4469 #CR-2182 Updated 5G disconnection issue fix (due to country update after connection).

Revision num 57391.
	#RSC-4686 #CR-2218 Added Fix for power constraint handling and max_reg_pwr value.

Revision num 57394.
	#RSC-4664 #CR-2198 Added fix to update beacon miss period for listen interval based sleep.	

Revision num 57395.
	#RSC-4703 #CR-2203 Added fix to error handling of CFG configurable parameters in AP mode.

Revision num 57439.
	#WLAN-4697 #CR-2011 Added changes for memory leak in driver with ni pointer.
	
Revision num 57519.
	#RSC-4777 #CR-2234 Limited updating max_reg power from beacon only,not from probe resp.

Revision num 57521.
	#WLAN-5028 #CR-2221 Added error handling for wrong operating modes.

Revision num 57523.
	#WLAN-5020 #CR-2220 Added limits to the ht_conf input values.

Revision num 57524.
	#RSC-4783 #CR-2225 Added fix to make operating mode 17(wlan_zigbee) work.

Revision num 57525.
	#WLAN-5053 #CR-2236 Fixed lock assert issue in ACS flow. 

Revision num 57526.
	#WLAN-5057 #CR-2233 Added taking MAC address input from User.

Revision num 57527.
	#WLAN-5027 #CR-2237 Updated coex mode insert scripts.

Revision num 57528.
	#RSC-4532 #CR-2217 Fix for crash while regression with iwconfig. 

Revision num 57536.
	#WLAN-5030 #CR-2223 Fix for dump stack while running ACS and HT40. 

Revision num 57537.
	#Updated Driver release version number to 1.1.a.

Revision num 57541.
	#WLAN-5041 #CR-2235 Fixed IC lock issue in DFS CAC algorithm.

Revision num 57614.
	#WLAN-5047 #CR-2242 Added error handling for get_privacy command.

Revision num 57615.
	#RSC-4794 #CR-2247 Fixed warning message while compilation.

Revision num 57622.
	#WLAN-5043 #CR-2245 Added fix for the issue with same country in CFG80211 and supplicant.  

Revision num 57627.
	#RSC-4810 #CR-2251 Added fix to pick correct firmware in Zigbee PER mode.

Revision num 57637.
	#WLAN-5055 #CR-2244 Fixed bt_stats command arguments issue with 9113.

Revision num 57678.
	#Updated Driver release version number to 1.1.0b.

Revision num 57714.
	#RSC-4566 #CR-2227 Added updating WLAN gain tables dynamically from user.

Revision num 57727.
	#RSC-4566 #CR-2227 Removed disabled code and fixed issues in gain table writing.

Revision num 57831.
	#RSC-5060 #CR-2257 Updated driver module descriptions.

Revision num 57832.
	#CR-2287 Fix for dump stack for BSD case.

Revision num 57833.
	#WLAN-5076 #CR-2264 Fix for wrong Long Pulse RADAR detection.

Revision num 57858.
	#WLAN-5076 #CR-2264 Added improvements to the Long Pulse RADAR detection fix.

Revision num 57876.
	#WLAN-5018 #CR-2302 Added fix for crash when EAPOL failure.

Revision num 57898.
	#RSC-4801 #CR-2290 Fixed IC lock issue in DFS algorithm.

Revision num 57900.
	#WLAN-4927 #CR-2305 Added Makefile "Compilation Done Successfully" print handling.	

Revision num 57907.
	#RSC-4819 #CR-2263 Added changes to support kernel version 4.20.

Revision num 57909.
	#Reverted r57907 as compilation failure observed with 2.6 kernel.

Revision num 57910.
	#CR-2310 Added fix for host_scan_2g command channel list.
	
Revision num 57911.
	#CR-2311 Added fix to avoid programming wrong channel count in host scan.

Revision num 57940.
	#RSC-5142 #CR-2311 Added fix to program valid channel in BGSCAN command.

Revision num 57941.
	#RSC-5132 #CR-2321 Added fix to allow 2g channels 1-11 to do active scan in world_reg_domain.

Revision num 57942.
	#RSC-5125 #CR-2322 Added handling for STA AUTH failure state in concurrent mode	.

Revision num 57943.
	#RSC-5098 #CR-2323 Fixed issue with iwlist scan command in concurrent mode.

Revision num 57944.
	#CR-2301 Fixed compilation warnings observed.

Revision num 57966.
	#WLAN-5029 #WLAN-5044 #RSC-4800 #CR-2326 Fixed issue due to accessing hal_priv_vap during VAP deletion.

Revision num 57967.
	#RSC-5120 #CR-2325 Removed unused BGSCAN_SUPPORT compilation directive from makefile.

Revision num 57968.
	#RSC-4819 #CR-2263 Fixed compilation issue with r57907 and adding changes to support kernel version 4.20.
	#Production release for RS9113 v1.6.2 release.

Revision num 58178.
	#WLAN-5105 #CR-2336 Fixed RSI AP start failure in WEP security. 

Revision num 58179.
	#WLAN-5109 #CR-2337 Fixed multicast packet dropping based on PN in open security.

Revision num 58379.
	#Updated BT per application
	#Updated Driver release version number to 1.1.0e.
	
Revision num 58535.
	#WLAN-5126 #CR-2356 Added controlling LED enable/disable from common_insert.

Revision num 58551.
	#Updated Driver release version number to 1.1.0f.

Revision num 58572.
	#RSC-5204 #CR-2388 Fixed null pointer accessing in DO_BGSCAN ioctl process.

Revision num 58575.
	#CE-10383 #CR-2375 Fixed Zigbee compilation issue for 64bit systems.

Revision num 58651.
	#WLAN-5165 #CR-2427 Fixed AP fails to beacon if it connects to multiple clients on saberlite platform.

Revision num 58690.
	#Updated Driver release version number to 1.1.0g.

Revision num 58823.
	#CR-2302 Fixed lock issue with previous fix r57876.

Revision num 58824.
	#WLAN-5127 #CR-2400 Fixed showing wrong frequency for 5G 8&12 channels in scan results.

Revision num 58828.
	#WLAN-5160 #CR-2454 Removing BT macaddress hard coding details from common insert.

Revision num 58996.
	#RSC-4317 #CR-2084 Fixed card reset issue with ULP.

Revision num 58999.
	#RSC-5170 #CR-2401 Fixed get_country info ioctl.	

Revision num 59003.
	#Updated Driver release version number to 1.1.0.

Revision num 59026.
	#RSC-4593 #CR-2484 Fixed Data protected bit is not set in Action frames in 11W.

Revision num 59058.
	#CR-2497 Removed support for MAC address genration for 9116 uncaliberated modules.

Revision num 59093.
	#Updated nLink Driver release notes to 1.1.1a.

Revision num 59201.
	#WLAN-5171 #CR-2502 Fixed crash in 3.4 kernel while running hostapd.

Revision num 59202.
	#WLAN-5041 #CR-2504 dump stack when configure RSI_AP in DFS channels.

Revision num 59231.
	#Updated comments in common_insert.sh regarding operating voltage of board"
	#CR-2473  Added ZigBee PER MATLAB script changes.

Revision num 59249.
	#RSC-5535 #CR-2526 Fixed compilation warning.
 
Revision num 59250.
	#WLAN-5180 #CR-2523 Fixed kernel crash in p2p for kernel v4.15 and above.

Revision num 59259.
	#RSC-5303 #CR-2527 Fixed kernel crash on Wand board for STA_alone script regression.

Revision num 59343.
	#WLAN-5164 #CR-2539 Handled ni removal node table cleanup to fix memory leaks in WLAN alone case.	

Revision num 59343.
	#RSC-4105 #CR-2033 Fixed dump stack while running script with sleep and bgscan in coex mode on SDIO interface.

Revision num 59444.
	#RSC-5573 #CR-2554 Fixed AP mode crash while sending DEAUTH to the client.

Revision num 59700.
	#CR-2608 Added PER mode support for updating wlan gain table from host. 

Revision num 59726.
	#CR-2619 Added per support for BT ANT.

Revision num 59781.
  	#Removed Zigbee coex_mode info from common_insert.sh file.

Revision num 59900.
	#RSC-5749 #CR-2659 Fixed issue in handling EAPOL4 TX failure.

Revision num 59901.
	#RSC-5623 #CR-2586 Fixed warning message in compilation.

Revision num 59904.
	#RSC-5688 #CR-2658 Fixed crash while insert and removing STA.

Revision num 60011.
	#CR-2664 Added period based stats for BT.

Revision num 60111.
	#CR-2584 Added fix for context based crash in scan process.

Revision num 60122.
	#RSC-5693 #CR-2563 Added filter broadcast ioctl.

Revision num 60150.
	#CE-10663 #CR-2719 Added fix for beacon miss time disconnect failure.

Revision num 60151.
	#RSC-5765 #CR-2716 Added device_sleep_indication_gpio selection from common_insert.

Revision num 60178.
	#WLAN-5111 #CR-2688 Fixed kernel crash with wait_forever.

Revision num 60179.
	#RSC-5494 #CR-2654 Fixed kernel warning on wand board platform when configured RSI_AP.

Revision num 60217.
	#RSC-5544 #CR-2553 Updated beacon interval configuration limits check

Revision num 60301.
	#WLAN-5197 #CR-2708 Fixed AP mode connection and disconnect time crash.

Revision num 60302.
	#RSC-5784 #CR-2709 Update Driver kernel support to 5.1.6

Revision num 60311.
	#CR-2545 Adding suspend and resume improments done for fossil.

Revision num 60347.
	#RSC-5623 #CR-2586 Fixed compilation warnings.

Revision num 60350.
	#CE-10790 #CR-2616 Fixed crash while running start_sta.sh. 

Revision num 60351.
	#RSC-5117 #CR-2627 Fixed RSI_STA rejoin issue while delete and create rsi_ap vap in concurrent mode.

Revision num 60352.
	#CE-10355 #CR-2550 Added changes for Bridge mode for AP in NL80211 Mode.

Revision num 60356.
	#WLAN-5181 #CR-2562 Fixed issue in multiple P2P_Client connection to RSI P2P_GO.

Revision num 60403.
	#CR-2742 Handled compilation warnings.

Revision num 60440
	#RSC-5032 #CR-2291 Fixed issue in handling SA query failure. 

Revision num 60501
	#RSC-5872 Updated default value for SLEEP_CLK_SOURCE.

Revision num 60543
	#RSC-5892 Fixed max channel limit for BT PER.

Revision num 60870
	#RSC-5583 #CR-2803 Fixed kernel crash with network manager in AP+ACS mode.

Revision num 60889
	#RSC-5923 #CR-2815 Fixed issue due to bridge mode patch (CR-2550).

Revision num 60892
	#RSC-5886 #CR-2814 Fixed RSI STA aggreagtion enable failure. 

Revision num 60893
	#RSC-5938 #CR-2801 Fixed driver compilation issue.

Revision num 60894
	#RSC-5893 #CR-2785 Fix for Power save params changing after connection if command given before connection.

Revision num 61075
	#CE-11324 #CR-2862 Fixed compilation error in kernel versions below 2.6.38.

Revision num 61076
	#RSC-5625 #CR-2843 Fixed AP_connection_failure while switching from 2G to 5G in concurrent mode.

Revision num 61078
	#RSC-5899 #CR-2836 Fixed Encryption Key is showing ON state while connecting RSI_STA in open security mode.

Revision num 61079
	#CR-2838 Updated FEATURE_BITMAP_9116 parameter in common_insert.sh

Revision num 61082
	#RSC-6015 #CR-2833 Fixed issue in running AP in DFS channels with INDIA country domain.

Revision num 61084
	#RSC-6101 #CR-2866 Added Customer ID to 9116 version info display.

Revision num 61103
	#RSC-5441 #CR-2874 Added fix for host (ap_mode) scan failure if it contains DFS channel.

Revision num 61114
	#RSC-5530 #CR-2873 Updated handling of Mobility domain (MD) IE.

Revision num 61116
	#CR-2878 Hardcoded HW_BMISS to 9116.

Revision num 61218
	#CR-2878 Fixed issue of unable to start AP after starting STA in concurrent mode for 9116.

Revision num 63521
	#RSC-5920 #CR-2968 Added fix for dropping packets after disconnection and connection with heavy traffic.

Revision num 63525
	#CR-3356 Changed print zone for the print

Revision num 64618
	#Porting Changes from 1.2.0_SILK branch.

Revision num 64902
	#Adding Edesix bus fixes for power save.

Revision num 64928
	#Added version number printing as per latest updates"

Revision num 66759
	#RSC-7404 Fix for showing wrong data rate in iwconfig if user fixed TX rate.
	#Made Default short GI in case HT40.

Revision num 66777
	#CR-3686 Fixed Krnel paging issues on auto rate table preperation.	

Revision num 66946
	#RSC-7204 #CR-3510 Handled enabling power save after disconnection without wait event.

Revision num 66974
	#CR-3677 Fixed kernel compilation with 64bit systems with kernels below 3.19.	

Revision num 66975
	#RSC-6717 #CR-3228 Fixed Compilation error while compiling driver in kernel 3.0.35.

Revision num 66977
	#WLAN-5259 #CR-3425 Fixed compilation issue on kernel below 2.6.39.

Revision num 67246
	#CE-12379 #CR-3593 Fixed null pointer access in ht ie of beacon parsing.

Revision num 67247
	#RSC-6299 #CR-2945 Added support for kernel v5.3.

Revision num 67248
	#LRSC-3943 #CR-3417 Fixed rsi AP failure if 31 client connected. 

Revision num 67249
	#WLAN-5160 #CR-3100 Added BT MAC Hardcoding information in common_insert.

Revision num 67251
	#RSC-6227 #CR-3064 Fixed P2P client connection issue.

Revision num 67256
	#Updated BT feature bitmap information for Hardcode macaddress. 

Revision num 67522
	#RSC-7600 #CR-3883 Fixed wps pbs and pin connectivity failure issue with WPA2 security.

Revision num 67525
	#RSC-6939 #CR-3406 Fixed Rx failure issue after Firmware load in USB.
